SF1143B-4 Murata

RFM products are now Murata products. SF1143B-4 Designed for SDARS IF Receiver Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case 315.00 MHz Differential Input and Output Pb Complies with Directive 2002/95/EC (RoHS) SAW Filter Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 C Max Soldering Profile 265C for 10 s SMP-03-S Electrical Characteristics Characteristic Sym Notes Min Typ Max Units Nominal Center Frequency f 315.000 MHz C 1 Passband Insertion Loss at fc IL 15.1 17.0 dB 1dB Passband BW 6.35 7.05 MHz 1 Fast Amplitude Ripple over fc 6.35 MHz 1, 2 1.5 dB P-P Group Delay Variation over fc 6.35 MHz GDV 23 200 ns P-P Rejection 100 to fc-10.3 and fc+10.3 to fc+100 MHz 1, 2, 3 38 45 dB Operating Temperature Range T 1-40 +85 C A Differential Input and Output Impedance 250 ohms Case Style SMP-03-S 7 x 5 mm Nominal Footprint 6 Lid Symbolization (YY=year, WW=week, S=shift) See note 4 RFM SF1143B-4 YYWWS Electrical Connections Connection Port 1 Hot Port 1 Ground Return or Hot Port 2 Hot Port 2 Ground Return or Hot Case Ground Terminals 10 1 5 6 All Others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4.LRI or after the part number indicateslow rate initial productio andEN or indicatesengineering prototypes 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Tape and Reel Standard ANSI / EIA 481. 7. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 8. US and international patents may apply. 9. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. 2010-2014 by Murata Electronics N.A., Inc. SF1143B-4 (R) 3/19/14 Page 1 of 3 www.murata.com20.2 Tape and Reel Specifications B Nominal Size Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail 16.12.00 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Tolerance Ao 5.5 mm 0.1mm Bo 7.5 mm 0.1mm Ko 2.0 mm 0.1mm Pitch 8.0 mm 0.1mm W 16.0 mm 0.2mm PIN 1 USER DIRECTION OF FEED 2010-2014 by Murata Electronics N.A., Inc. www.murata.com SF1143B (R) 3/19/14 Page 2 of 3 13.0 100 REF. REF.