Only Reflow Soldering Chip Multilayer Ceramic Capacitors on Interposer Board for General Purpose ZRB18AR60J226ME01 (0603, X5R:EIA, 22uF, DC6.3V) : packaging code Reference Sheet 1.Scope This product specification is applied to Chip Multilayer Ceramic Capacitors on Interposer Board used for General Electronic equipment. This product is applied for Only Reflow Soldering. 2.MURATA Part NO. System (Ex.) ZRB 18 A R6 0J 226 M E01 L (1)L/W (2)T (3)Temperature (4)Rated (5)Nominal (6)Capacitance (7)Muratas Control (8)Packaging Code Dimensions Dimensions Characteristics Voltage Capacitance Tolerance Code 3. Type & Dimensions (Unit:mm) (1)-1 L (1)-2 W (2) T e g 1.60.2 0.80.2 1.00.2 0.2 to 0.65 0.6 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):X5R(EIA) (5) Nominal Methods Rated Capacitance (Operating Temp. coeff Temp. Range Capacitance Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) -55 to 85 C -15 to 15 % DC 6.3 V 22 uF 20 % -55 to 85 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel L 3000 pcs./Reel EMBOSSED W8P4 f330mm Reel K 8000 pcs./Reel EMBOSSED W8P4 Product specifications in this catalog are as of Mar.28,2019,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. ZRB18AR60J226ME01-01 1 Specifications and Test Methods Test Method Item Specification No (Ref. Standard:JIS C 5101, IEC60384 1 Rated Voltage Shown in Rated value. The rated voltage is defined as the maximum voltage which may be applied continuously to the capacitor. P-P O-P When AC voltage is superimposed on DC voltage, V or V , whichever is larger, should be maintained within the rated voltage range. 2 Appearance No defects or abnormalities. Visual inspection. 3 Dimension Within the specified dimensions. Using Measuring instrument of dimension. 4 Voltage proof No defects or abnormalities. Measurement Point :Between the terminations Test Voltage : 250% of the rated voltage Applied Time : 1 to 5 s Charge/discharge current : 50mA max. To apply the test voltage through the Interposer board termination. 5 Insulation Resistance(I.R.) More than 2000M or 50 F (Whichever is smaller) Measurement Point : Between the terminations Measurement Voltage : DC Rated Voltage Charging Time : 1 min Charge/discharge current : 50mA max. Measurement Temperature: Room Temperature To apply the test voltage through the Interposer board termination. 6 Capacitance Shown in Rated value. Measurement Temperature: Room Temperature Capacitance Frequency Voltage 7 Dissipation Factor (D.F.) 0.1 max. C10F 1.0+/-0.1kHz 1.0+/-0.2Vrms (10V min.) C10F 1.0+/-0.1kHz 0.5+/-0.1Vrms (6.3V max.) C10F 120+/-24Hz 0.5+/-0.1Vrms To apply the test voltage through the Interposer board termination. 8 Temperature No bias R6 : Within +/-15% (-55C to +85C) The capacitance change should be measured after 5 min. Characteristics R7 : Within +/-15% (-55C to +125C) at each specified temp. stage. of Capacitance C8 : Within +/-22% (-55C to +105C) Capacitance value as a reference is the value in step 3. D7 : Within +22/-33% (-55C to +125C) Measurement Voltage : Less than 1.0Vrms (Refer to the individual data sheet) Step Temperature( C) Applying Voltage(VDC) 1 Reference Temp.+/-2 2 Min.Operating Temp. +/-3 3 Reference Temp. +/-2 No bias 4 Max.Operating Temp. +/-3 5 Reference Temp. +/-2 To apply the test voltage through the Interposer board termination. Initial measurement Perform a heat treatment at 150+0/-10C for 1h and then let sit for 24+/-2h at room temperature,then measure. 9 Adhesive Strength No removal of the terminations or other defect Solder the capacitor on the test substrate shown in Fig.3. of Termination should occur. Applied Force: 5N Holding Time : 10+/-1s Applied Direction : In parallel with the test substrate and vertical with the capacitor side. 10 Vibration Appearance No defects or abnormalities. Solder the capacitor on the test substrate shown in Fig.3. Capacitance Within the specified initial value. Kind of Vibration : A simple harmonic motion 10Hz to 55Hz to 10Hz (1min) Total amplitude :1.5mm D.F. Within the specified initial value. This motion should be applied for a period of 2h in each 3 mutually perpendicular directions(total of 6h). JEMCGS-05966 2