MODM7AE70 Ethernet Core Module 100 Version with RJ-45 200 Version with 10-pin header DATASHEET Key Points Use as a high-performance single board Customize with a development kit and begin computer or add Ethernet connectivity writing application code immediately to a new or existing design Industrial temperature range (-40C to 85C) Device Connectivity 10/100Mbps Ethernet with IEEE1588 PTP 1 Digital to Analog (DAC) Output frames and 802.3az Energy-effecient support 53 digital I/Os 2 Up to 2 USARTs, 5 UARTs, 3 I C, and 4 SPI 16-bit External Bus Interface 11 Analog to Digital (ADC) Inputs Performance and memory 32-bit 300 MHz Processor 8MB SDRAM and 2MB Flash Companion development kit The following is available with the development kit: Customize any aspect of operation including web pages, data filtering, or custom network applications Development software: NB Eclipse IDE, Graphical debugger, deployment tools, and examples Communication software: TCP/IP stack, HTTPS web server, FTP, E-mail, and flash file system System software: uC/OS RTOS, ANSI C/C++ compiler and linker Security software: Embedded SSL/TLS & SSH libraries The following optional software modules are not included with kit and are sold separately: SNMP Updated: August 10, 2021 Page 1 of 13 2021 NetBurner Inc. All Rights Reserved.MODM7AE70 Specifications Processor and Memory Microchip SAM E70 32-bit ARM Cortex -M7 processor running at 300 MHz clock speed with 8MB SDRAM, 2MB em- 1 bedded flash, 384Kb embedded multi-port SRAM, and 1KB embedded low-power backup RAM . Single and double precision hardware Floating Point Unit (FPU), DSP Instructions, Thumb -2 Instruction Set. 1. While the RAM is usable, it is unsuitable for low-power backup due to the power consumption of the modules components. Network Interface 10/100 BaseT with RJ-45 connector (100 Version) 10-pin header (200 Version) Data I/O Interface (P1 and P2) Up to 7 Asynchronous Serial Ports: 2 16-bit external bus interface USARTs, 5 Two-wire UARTs Image Sensor Interface (ISI) Up to 53 digital I/O Quad SPI Interface Up to 3 Two-Wire Interfaces (TWIHS)(I2C-compatible) 11 Analog to Digital (ADC) Inputs Up to 4 SPI interface 1 Digital to Analog (DAC) Output SD/MMC flash card ready SPI Configurations The SPI interfaces are available from the following: 1 dedicated SPI 1 Quad SPI that can be configured to run as a native SPI or QSPI 2 from USART0 and USART1 that can be configured as SPI Serial Configurations The UARTs can be configured in the following ways: USART0/1 ISO7816 IrDA RS-422/485 Manchester Note: USART0/1 supports SPI. USART1 supports Modem and LON mode. Additional Peripherals Ethernet AVB support with IEEE802.1AS Time-stamping and IEEE802.1Qav credit-based traffic-shaping hardware support. Two master Controller Area Networks (MCAN) with Flexible Data Rate (CAN-FD) with SRAM-based mailboxes, time- and event-triggered transmission. Serial Synchronous Controller (SSC) with I2S and TDM support. High-speed Multimedia Card Interface (HSMCI) (SDIO/SD Card/e.MMC) Nine 16-bit Timer/Counters, can be chained to create 32 bit and 48 bit timer/counters. Functions include capture, compare, interrupt generation, frequency measurement, event counting, interval measurement, quadrature decoder, pulse generation, waveform generation, synchronization with PWM peripheral, delay timing pulse width modulation, 2-bit Gray Up/Down Counter for stepper motor control. Each channel has Updated: August 10, 2021 Page 2 of 13 2021 NetBurner Inc. All Rights Reserved.