CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Chip Type, Low ESR, Higher Capacitance PCJ PCK Low ESR, Higher Capacitance, High ripple current. Low ESR Load life of 2000 hours at 105C. SMD type : Lead free reflow soldering condition at 260C peak correspondence. PCJ Compliant to the RoHS directive (2011/65/EU). Low ESR Higher Capacitance, PCF Specifications Item Performance Characteristics Category Temperature Range 55 to +105C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 33 to 2700F Capacitance Tolerance 20% at 120Hz, 20C Tangent of loss angle (tan ) Less than or equal to the specified value at 120Hz, 20C ( 1) ESR Less than or equal to the specified value at 100kHz, 20C Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes application of rated voltage at 20C Temperature Characteristics Z+105C / Z+20C 1.25 (100kHz) Z55C / Z+20C 1.25 (Max.Impedance Ratio) Capacitance change Within 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan 150% or less than the initial specified value Endurance capacitors are restored to 20C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 2000 hours at 105C. Leakage current ( 2) Less than or equal to the initial specified value Capacitance change Within 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan 150% or less than the initial specified value capacitors are restored to 20C after the rated voltage is ESR ( 1) 150% or less than the initial specified value (Steady State) applied for 1000 hours at 60C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions Capacitance change Within 10% of the initial capacitance value ( 3) prescribed here, the capacitor shall meet the specifications listed at tan 130% or less than the initial specified value right. ESR ( 1) Pre-heating shall be done at 150 to 200C and for 60 to 180 sec. 130% or less than the initial specified value The duration for over +230C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value Resistance to not exceed 60 seconds. In case peak temperature is 250C or less, reflow soldering shall be Soldering Heat two times maximum. In case peak temperature is 260C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 6.3V 220F) Dimensions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Positive P C J 0 J 2 2 1 M C L 1 G S Plastic platform Capacitance Lot No. 0.3 MAX. C0.2 Taping code Size code Configuration Capacitance tolerance (20%) Rated capacitance (220F) +0.1 Rated voltage (6.3V) L -0.4 Series Voltage ( j:6.3v) H Negative Series name Type (mm) Voltage Size 5 6L 6.3 6L 6.3 8L 8 7L 8 8L 8 10L 8 12L 10 8L 10 10L 10 12.7L 5.0 6.3 6.3 8.0 8.0 8.0 8.0 10.0 10.0 10.0 D V 2.5 4 6.3 10 16 5.9 5.9 7.9 6.9 7.9 9.9 11.9 7.9 9.9 12.6 L Code e g j A C 6.0 7.3 7.3 9.0 9.0 9.0 9.0 11.0 11.0 11.0 A 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3 B Frequency coefficient of rated ripple current 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3 C 1.6 2.1 2.1 3.2 3.2 3.2 3.2 4.6 4.6 4.6 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more E 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Coefficient 0.05 0.30 0.70 1.00 H Dimension table in next page. 41 C J 2 2 0 j 8 4 1 D0.5 B0.2 E 0.5 MAX. A0.2CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCJ Standard Ratings Rated Voltage Surge Voltage Rated Capacitance Case Size Leakage Current ESR (m) Rated Ripple tan Part Number (V)(code) (V) (F) D L (mm) (A) (at 100kHz 20C) (mArms) 180 5 6 0.12 90 21 2670 PCJ0E181MCL1GS 390 6.3 6 0.12 195 15 3400 PCJ0E391MCL1GS 470 6.3 8 0.12 235 13 3600 PCJ0E471MCL1GS 560 6.3 8 0.12 280 13 3600 PCJ0E561MCL4GS 280 13 4100 PCJ0E561MCL1GS 560 8 7 0.12 680 8 7 0.12 340 13 4100 PCJ0E681MCL1GS 820 8 8 0.12 410 12 4260 PCJ0E821MCL6GS 2.5 2.8 820 8 12 0.12 410 9 5400 PCJ0E821MCL1GS (0E) 1000 8 8 0.12 500 12 4260 PCJ0E102MCL1GS 1200 10 8 0.12 600 13 4800 PCJ0E122MCL1GS 1500 8 10 0.12 750 10 5220 PCJ0E152MCL6GS 1500 8 12 0.12 750 9 5400 PCJ0E152MCL1GS 2200 10 10 0.12 1100 10 5500 PCJ0E222MCL1GS 2700 10 12.7 0.12 1350 9 5800 PCJ0E272MCL1GS 100 5 6 0.12 80 22 2610 PCJ0G101MCL1GS 150 5 6 0.12 120 22 2610 PCJ0G151MCL1GS 270 6.3 6 0.12 216 15 3200 PCJ0G271MCL1GS 330 6.3 6 0.12 264 15 3300 PCJ0G331MCL1GS 312 14 3470 PCJ0G391MCL1GS 390 6.3 8 0.12 470 8 7 0.12 376 14 3950 PCJ0G471MCL1GS 560 8 7 0.12 448 14 4000 PCJ0G561MCL1GS 560 8 12 0.12 448 9 5200 PCJ0G561MCL9GS 680 8 8 0.12 544 13 3950 PCJ0G681MCL1GS 4 1000 8 10 0.12 800 10 5220 PCJ0G102MCL4GS 4.6 (0G) 1000 10 8 0.12 800 13 4300 PCJ0G102MCL1GS 1200 8 12 0.12 960 9 5400 PCJ0G122MCL1GS 1200 10 10 0.12 960 10 5500 PCJ0G122MCL6GS 1200 1500 8 12 0.12 9 5200 PCJ0G152MCL4GS 1500 10 10 0.12 1200 10 5500 PCJ0G152MCL1GS 1800 10 10 0.12 1440 10 5500 PCJ0G182MCL1GS 1800 10 12.7 0.12 1440 9 5600 PCJ0G182MCL9GS 2200 10 12.7 0.12 1760 9 5700 PCJ0G222MCL1GS 126 24 2500 PCJ0J101MCL1GS 100 5 6 0.12 120 5 6 0.12 151 24 2500 PCJ0J121MCL1GS 220 6.3 6 0.12 277 15 3200 PCJ0J221MCL1GS 270 6.3 8 0.12 340 14 3470 PCJ0J271MCL1GS 330 6.3 8 0.12 416 14 3470 PCJ0J331MCL4GS 0.12 416 14 3950 PCJ0J331MCL1GS 330 8 7 390 8 7 0.12 491 14 3950 PCJ0J391MCL1GS 6.3 7.2 470 8 8 0.12 592 13 3950 PCJ0J471MCL1GS (0J) 820 8 10 0.12 1033 12 4770 PCJ0J821MCL6GS 1033 820 8 12 0.12 10 5150 PCJ0J821MCL4GS 820 10 8 0.12 1033 13 4500 PCJ0J821MCL1GS 1200 10 10 0.12 1512 12 5025 PCJ0J122MCL1GS 1500 10 10 0.12 1890 12 5025 PCJ0J152MCL1GS 1500 10 12.7 0.12 1890 10 5500 PCJ0J152MCL9GS 2268 5200 PCJ0J182MCL1GS 1800 10 12.7 0.12 11 47 5 6 0.12 94 28 2310 PCJ1A470MCL1GS 56 5 6 0.12 112 28 2310 PCJ1A560MCL1GS 68 5 6 0.12 136 28 2310 PCJ1A680MCL1GS 120 6.3 6 0.12 240 25 2530 PCJ1A121MCL1GS 0.12 300 21 2880 PCJ1A151MCL1GS 150 6.3 8 10 11.5 220 8 7 0.12 440 21 3220 PCJ1A221MCL1GS (1A) 270 8 7 0.12 540 21 3220 PCJ1A271MCL1GS 330 8 8 0.12 660 19 3390 PCJ1A331MCL1GS 780 390 8 10 0.12 17 4000 PCJ1A391MCL1GS 470 10 8 0.12 940 19 3800 PCJ1A471MCL1GS 680 10 10 0.12 1360 13 4820 PCJ1A681MCL1GS 33 5 6 0.12 105 35 2070 PCJ1C330MCL1GS 39 5 6 0.12 125 35 2070 PCJ1C390MCL1GS 217 68 6.3 6 0.12 28 2390 PCJ1C680MCL1GS 82 6.3 8 0.12 262 24 2700 PCJ1C820MCL1GS 100 6.3 8 0.12 320 24 2700 PCJ1C101MCL4GS 100 8 7 0.12 320 24 3010 PCJ1C101MCL1GS 16 384 18.4 120 8 7 0.12 24 3010 PCJ1C121MCL1GS (1C) 0.12 480 22 3150 PCJ1C151MCL1GS 150 8 8 180 8 10 0.12 576 18 3890 PCJ1C181MCL1GS 220 8 10 0.12 704 18 3890 PCJ1C221MCL4GS 220 10 8 0.12 704 22 3450 PCJ1C221MCL1GS 864 270 8 12 0.12 16 4070 PCJ1C271MCL1GS 330 10 10 0.12 1056 16 4350 PCJ1C331MCL1GS Rated ripple current (mArms) at 105C 100kHz No marked, 1 will be put at 12th digit of type numbering system. Taping specifications are given in page 23. : In this case, 4 will be put at 12th digit of type numbering system. Recommended land size, soldering by reflow are given in page 18, 19. : In this case, 6 will be put at 12th digit of type numbering system. Please refer to page 3 for the minimum order quantity. : In this case, 9 will be put at 12th digit of type numbering system. 42