CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Chip Type, Ultra-low ESR CK series Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105C. SMD type : Lead free reflow soldering condition at 260C peak correspondence. Compliant to the RoHS directive (2011/65/EU). CJ Low ESR CK Specifications Item Performance Characteristics Category Temperature Range 55 to +105C Rated Voltage Range 2.5 to 6.3V Rated Capacitance Range 220 to 2200F Capacitance Tolerance 20% at 120Hz, 20C Tangent of loss angle (tan ) Less than or equal to the specified value at 120Hz, 20C ( 1) ESR Less than or equal to the specified value at 100kHz, 20C Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes application of rated voltage at 20C Temperature Characteristics Z+105C / Z+20C 1.25 (100kHz) Z55C / Z+20C 1.25 (Max.Impedance Ratio) Within 20% of the initial capacitance value ( 3) Capacitance change The specifications listed at right shall be met when the tan 150% or less than the initial specified value Endurance capacitors are restored to 20C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 2000 hours at 105C. Leakage current ( 2) Less than or equal to the initial specified value Capacitance change Within 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan 150% or less than the initial specified value capacitors are restored to 20C after the rated voltage is ESR ( 1) 150% or less than the initial specified value (Steady State) applied for 1000 hours at 60C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions Capacitance change Within 10% of the initial capacitance value ( 3) prescribed here, the capacitor shall meet the specifications listed at tan 130% or less than the initial specified value right. ESR ( 1) Pre-heating shall be done at 150 to 200C and for 60 to 180 sec. 130% or less than the initial specified value The duration for over +230C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value Resistance to not exceed 60 seconds. In case peak temperature is 250C or less, reflow soldering shall be Soldering Heat two times maximum. In case peak temperature is 260C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 6.3V 220F) Dimensions Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Plastic platform Capacitance Lot No. 0.3 MAX. C0.2 P C K 0 J 2 2 1 M C O 1 G S Taping code Configuration Capacitance tolerance (20%) +0.1 L Rated capacitance (220F) Voltage ( j:6.3v) -0.4 Series Negative Rated voltage (6.3V) H Series name Type (mm) 6.3 6L 8 7L 10 8L 10 10L Size 6.3 8.0 10.0 10.0 D 5.9 6.9 7.9 9.9 L 7.3 9.0 11.0 11.0 A 6.6 8.3 10.3 10.3 B Voltage 6.6 8.3 10.3 10.3 C V 2.5 4 6.3 2.1 3.2 4.6 4.6 E Code e g j H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. CAT.8100D C K 2 2 0 j 9 4 1 D0.5 B0.2 E 0.5 MAX. A0.2CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CKseries Standard Ratings Rated Voltage Surge Voltage Rated Capacitance Case Size Leakage Current ESR (m) Rated Ripple tan Part Number (V)(code) (V) (F) D L (mm) (A) (at 100kHz 20C) (mArms) 390 6.3 6 0.12 293 10 3900 PCK0E391MCO1GS 560 8 7 0.12 420 9 4500 PCK0E561MCO1GS 2.5 680 8 7 0.12 510 9 4500 PCK0E681MCO1GS 2.8 (0E) 1200 10 8 0.12 900 9 5000 PCK0E122MCO1GS 2200 10 10 0.12 1650 8 6000 PCK0E222MCO1GS 330 6.3 6 0.12 396 10 3900 PCK0G331MCO1GS 470 8 7 0.12 564 9 4500 PCK0G471MCO1GS 4 4.6 560 8 7 0.12 672 9 4500 PCK0G561MCO1GS (0G) 1000 10 8 0.12 1200 9 5000 PCK0G102MCO1GS 1800 10 10 0.12 2160 8 6000 PCK0G182MCO1GS 220 6.3 6 0.12 416 10 3900 PCK0J221MCO1GS 330 8 7 0.12 624 9 4500 PCK0J331MCO1GS 6.3 7.2 390 8 7 0.12 737 9 4500 PCK0J391MCO1GS (0J) 820 10 8 0.12 1550 9 5000 PCK0J821MCO1GS 1500 10 10 0.12 2835 8 6000 PCK0J152MCO1GS Rated ripple current (mArms) at 105C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D