CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Chip Type, High Voltage / Long Life CX series High reliability, High voltage (to 50V). Low ESR, High ripple current. Long life of 1500 to 3000 hours at 125C. CX SMD type : Lead free reflow soldering condition at 260C peak complete correspondence. Higher Adapted to the RoHS directive (2002/95/EC). Temperature CV Specifications Item Performance Characteristics Category Temperature Range 55 to +125C Rated Voltage Range 16 to 50V Rated Capacitance Range 5.6 to 390F Capacitance Tolerance 20% at 120Hz, 20C Tangent of loss angle (tan ) Less than or equal to the specified value at 120Hz, 20C (1) Less than or equal to the specified value 100kHz, 20C ESR at Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes application of rated voltage at 20C Temperature Characteristics Z+125C / Z+20C 1.25 (100kHz) Z55C / Z+20C 1.25 (Max.Impedance Ratio) Capacitance change Within 20% of initial capacitance value ( 3) The specifications listed at below shall be met when the tan 150% or less of the initial specified value capacitors are restored to 20C after the rated voltage is Endurance ESR(1) 150% or less of the initial specified value applied for 3000 hours (D 6.3:1500hours) at 125C. Leakage current ( 2) Less than or equal to the initial specified value Capacitance change Within 20% of initial capacitance value ( 3) The specifications listed at below shall be met when the Damp Heat tan 150% or less of the initial specified value capacitors are restored to 20C after the rated voltage is ESR(1) (Steady State) 150% or less of the initial specified value applied for 1000 hours at 60C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it s temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200C and for 60 to 180 sec. Capacitance change Within 10% of the initial capacitance value ( 3) The duration for over +230C temperature at capacitor surface shall tan Resistance to 130% or less than the initial specified value not exceed 60 seconds. ESR(1) 130% or less than the initial specified value Soldering Heat In the case of peak temp, less than 250C, reflow soldering shall be Leakage current ( 2) Less than or equal to the initial specified value two times maximum. In the case of peak temp, less than 260C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 35V 39F) Dimensions Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Plastic platform Capacitance Lot No. 0.3 MAX. C0.2 P C X 1 V 3 9 0 M C L 1 G S Taping code Size code Configuration Capacitance toleranc (20%) Rated capacitance (39 F) +0.1 Rated voltage (35V) L -0.4 Voltage (V:35V) Series Negative Series name H Type (mm) Size 6.3 6L 8 7L 8 10L 8 12L 10 8L 10 10L 10 12.7L D 6.3 8.0 8.0 8.0 10.0 10.0 10.0 L 5.9 6.9 9.9 11.9 7.9 9.9 12.6 A 7.3 9.0 9.0 9.0 11.0 11.0 11.0 B 6.6 8.3 8.3 8.3 10.3 10.3 10.3 Voltage C 6.6 8.3 8.3 8.3 10.3 10.3 10.3 V 16 20 25 35 50 E 2.1 3.2 3.2 3.2 4.6 4.6 4.6 Code C D E V H H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. CAT.8100A CX 39 V 012 D + 0.5 MAX. B0.2 E 0.5 MAX. A0.2CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CXseries Standard Ratings Rated Ripple (mArms) Case Size Rated Voltage Surge Voltage Rated Capacitance Leakage Current ESR (m ) tan Part Number (at 100kHz 20 C) (V)(code) (V) ( F) D L (mm) ( A) 47 6.3 6 0.12 150 55 1000 390 PCX1C470MCL1GS 82 8 7 0.12 262 45 1300 530 PCX1C820MCL1GS 150 8 10 0.12 480 28 2000 780 PCX1C151MCL6GS 16 150 10 8 0.12 480 33 1900 830 PCX1C151MCL1GS 18.4 (1C) 220 8 12 0.12 704 27 2300 870 PCX1C221MCL1GS 270 10 10 0.12 864 27 2300 830 PCX1C271MCL1GS 390 10 12.7 0.12 1248 26 2700 1040 PCX1C391MCL1GS 33 6.3 6 0.12 132 60 900 380 PCX1D330MCL1GS 56 8 7 0.12 224 50 1300 500 PCX1D560MCL1GS 120 8 10 0.12 480 29 1900 770 PCX1D121MCL6GS 20 23.0 120 10 8 0.12 480 35 1800 810 PCX1D121MCL1GS (1D) 150 8 12 0.12 600 28 2200 860 PCX1D151MCL1GS 180 0.12 720 28 2300 800 PCX1D181MCL1GS 10 10 270 10 12.7 0.12 1080 27 2700 1020 PCX1D271MCL1GS 22 6.3 6 0.12 110 65 900 360 PCX1E220MCL1GS 39 0.12 195 55 1200 480 PCX1E390MCL1GS 8 7 82 8 10 0.12 410 30 1900 760 PCX1E820MCL6GS 25 28.7 82 10 8 0.12 410 36 1800 800 PCX1E820MCL1GS (1E) 120 0.12 600 29 2200 850 PCX1E121MCL6GS 8 12 120 10 10 0.12 600 29 2200 790 PCX1E121MCL1GS 180 10 12.7 0.12 900 28 2600 1010 PCX1E181MCL1GS 10 0.12 70 85 800 310 PCX1V100MCL1GS 6.3 6 18 8 7 0.12 126 60 1100 450 PCX1V180MCL1GS 39 8 10 0.12 273 35 1800 700 PCX1V390MCL6GS 35 40.2 39 10 8 0.12 273 41 1700 750 PCX1V390MCL1GS (1V) 56 8 12 0.12 392 33 2000 780 PCX1V560MCL1GS 68 10 10 0.12 476 30 2200 740 PCX1V680MCL1GS 100 10 12.7 0.12 700 29 2600 990 PCX1V101MCL1GS 5.6 6.3 6 0.12 56 105 700 280 PCX1H5R6MCL1GS 10 8 7 0.12 100 75 1000 410 PCX1H100MCL1GS 22 8 10 0.12 220 37 1700 680 PCX1H220MCL6GS 50 57.5 22 10 8 0.12 220 56 1400 730 PCX1H220MCL1GS (1H) 27 8 12 0.12 270 35 2000 760 PCX1H270MCL1GS 33 10 10 0.12 330 31 2200 630 PCX1H330MCL1GS 47 10 12.7 0.12 470 30 2500 970 PCX1H470MCL1GS Ambient temperature of a capacitor Rated ripple current (mArms) at 105C 100kHz No marked, 1 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100A