CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Chip Type, Higher Capacitance NEW High Temperature Range PCZ High reliability. Low ESR, High ripple current. Long life of 2000 hours at 150C. SMD type : Lead free reflow soldering condition at 260C peak complete correspondence. High Temperature PCH Compliant to the RoHS directive (2011/65/EU). PCZ ESR after Endurance at -40C. AEC-Q200 compliant. Please contact us for details. Specifications Item Performance Characteristics Category Temperature Range 55 to +150C Rated Voltage Range 25 to 35V Rated Capacitance Range 100 to 330F Capacitance Tolerance 20% at 120Hz, 20C Less than or equal to the specified value 120Hz, 20C Tangent of loss angle (tan ) at ESR ( 1) Less than or equal to the specified value at 100kHz, 20C Leakage Current ( 2) After 2 minutes application of rated voltage, leakage current is not more than 0.03CV or 3(A), whichever is greater. Temperature Characteristics Z55C / Z+20C 1.25 (100kHz) (Max.Impedance Ratio) Capacitance change Within 20% of initial capacitance value ( 3) The specifications listed at right shall be met when the tan 150% or less of the initial specified value Endurance capacitors are restored to 20C after the rated voltage is ( 1) ESR 200% or less of the initial specified value applied for 2000 hours at 150C. Leakage current ( 2) Less than or equal to the initial specified value ESR after Endurance ( 1) Less than or equal to the specified value at 100kHz, -40C Capacitance change Within 20% of initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan 150% or less of the initial specified value capacitors are restored to 20C after the rated voltage is ( 1) ESR 200% or less of the initial specified value (Steady State) applied for 2000 hours at 85C, 85% RH. Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Capacitance change Within 10% of the initial capacitance value ( 3) Pre-heating shall be done at 150 to 200C and for 60 to 180 sec. 130% or less than the initial specified value Resistance to tan The duration for over +230C temperature at capacitor surface shall ( 1) ESR 130% or less than the initial specified value Soldering Heat not exceed 60 seconds. Leakage current ( 2) Less than or equal to the initial specified value In case peak temperature is 260C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 35V 220F) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Dimensions P C Z 1 V 2 2 1 M C L 1 G S Positive Taping code Plastic platform Size code Capacitance Lot No. 0.3 MAX. C0.2 Configuration Capacitance tolerance (20%) Rated capacitance (220F) Rated voltage (35V) Series name Type L0.5 Voltage (V:35V) Series Negative H (mm) Voltage 8 10L 10 10L 10 12.7L Size V 25 35 8.0 10.0 10.0 D Code E V 9.9 9.9 12.6 L 9.0 11.0 11.0 A B 8.3 10.3 10.3 Frequency coefficient of rated ripple current 8.3 10.3 10.3 C 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more E 3.2 4.6 4.6 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Coefficient 0.05 0.30 0.70 1.00 H A p r. 2 019 C Z 2 2 0 V 0 1 2 D0.5 B0.2 E 0.5 MAX. A0.2CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCZ Dimensions Low temp. Initial ESR after Rated Ripple Rated Voltage Surge Voltage Rated Capacitance Case Size ESR Endurance tan (mArms) Part Number (m) (V)(code) (V) (F) D L (mm) (m) (150C / 100kHz) (20C / 100kHz) (-40C / 100kHz) 150 8 10 0.08 20 40 1800 PCZ1E151MCL6GS 25 31 270 10 10 0.08 20 40 1800 PCZ1E271MCL1GS (1E) 330 10 12.7 0.08 15 30 2100 PCZ1E331MCL1GS 8 10 100 0.08 22 44 1700 PCZ1V101MCL6GS 35 43 180 10 10 0.08 20 40 1800 PCZ1V181MCL1GS (1V) 220 10 12.7 0.08 16 32 2000 PCZ1V221MCL1GS No marked, 1 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system.