CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Standard
PLF
Low ESR, High ripple current.
Load life of 2000 hours at 105C.
PLG
Radial lead type :
Lead free flow soldering condition correspondence.
Higher
Compliant to the RoHS directive (2011/65/EU).
Capacitance
Long Life Low ESR
PLS PLE
PLF
Specifications
Item Performance Characteristics
Category Temperature Range 55 to +105C
Rated Voltage Range
2.5 to 25V
Rated Capacitance Range 6.8 to 1500F
Capacitance Tolerance 20% at 120Hz, 20C
Tangent of loss angle (tan ) Less than or equal to the specified value 120Hz, 20C
at
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20C
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20C
Temperature Characteristics
Z+105C / Z+20C 1.25 (100kHz)
(Max.Impedance Ratio) Z55C / Z+20C 1.25
Capacitance change Within 20% of the initial capacitance value ( 3)
The specifications listed at right shall be met when the
150% or less than the initial specified value
tan
Endurance capacitors are restored to 20C after the rated voltage is
( 1)
ESR 150% or less than the initial specified value
applied for 2000 hours at 105C.
Leakage current ( 2)
Less than or equal to the initial specified value
( )
Capacitance change Within 20% of the initial capacitance value 3
The specifications listed at right shall be met when the
Damp Heat tan 150% or less than the initial specified value
capacitors are restored to 20C after the rated voltage is
ESR ( 1) 150% or less than the initial specified value
(Steady State)
applied for 1000 hours at 60C, 90% RH.
Leakage current ( 2)
Less than or equal to the initial specified value
After soldering the capacitor under the soldering conditions
( )
Capacitance change Within 10% of the initial capacitance value 3
prescribed here as preheat at 150 to 200C for 60 to 180 seconds
tan 130% or less than the initial specified value
Resistance to
and peak temperature at 265C for 10 seconds or less, the
ESR ( 1) 130% or less than the initial specified value
capacitor shall meet the specifications listed at right, provided that
Soldering Heat
Leakage current ( 2)
Less than or equal to the initial specified value
its temperature profile is measured at both of terminal ends facing
the soldering side.
Marking Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 4V 560 F)
Capacitance Resin coated Case
1 2 3 4 5 6 7 8 9 10 11 12
Voltage(g:4V)
P L F 0 G 5 6 1 M D O 1
Size code
Configuration
d Capacitance tolerance (20%)
Series
Lot. No.
Rated capacitance (560F)
+0.5MAX.
L 15MIN 4MIN
Rated voltage (4V)
Series name
Type
(mm)
Voltage
Size 6.3 6L 6.3 9L 6.3 10.5L 8 7L 8 9L 8 12L 10 8L 10 10L 10 13L
V 2.5 4 6.3 10 16 20 25
6.3 6.3 6.3 8.0 8.0 8.0 10.0 10.0 10.0
D
Code e g j A C D E
5.5 8.5 10.0 6.5 8.5 11.5 7.5 9.5 12.5
L
2.5 2.5 2.5 3.5 3.5 3.5 5.0 5.0 5.0
P
Frequency coefficient of rated ripple current
0.45 0.6 0.5 0.6 0.6 0.6 0.6 0.6 0.6
d
0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more
Coefficient 0.05 0.30 0.70 1.00
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
56
L F
5 6 0
g
8 4 1
D0.5
0.5
PCONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
PLF
Standard Ratings
Rated Voltage Surge Voltage Rated Capacitance Case Size Leakage Current ESR (m) Rated Ripple
tan Part Number
(V)(code) (V) (F) D L (mm) (A) (at 100kHz 20C) (mArms)
330 6.3 9 0.08 500 7 5600 PLF0E331MCO8
390 6.3 10.5 0.08 195 20 3200 PLF0E391MDL4
560 6.3 9 0.08 500 7 5600 PLF0E561MCO8
560 8 9 0.08 280 6 4800 PLF0E561MCO1
680 8 9 0.08 340 7 4800 PLF0E681MCO6
680 8 12 0.08 340 6 5700 PLF0E681MDO1
2.5
2.8 820 6.3 9 0.08 500 7 5600 PLF0E821MCO8
(0E)
820 8 9 0.08 410 7 5200 PLF0E821MCO6
820 8 12 0.08 410 6 6200 PLF0E821MDO1
1000 10 13 0.08 500 6 6500 PLF0E102MDO1
1200 10 13 0.08 600 8 5300 PLF0E122MDO1
8 12 0.08 7 6100 PLF0E152MDO6
1500 750
1500 10 13 0.08 750 8 5500 PLF0E152MDO1
270 6.3 9 0.08 500 7 5600 PLF0G271MCO8
6.3 10.5 0.08 PLF0G271MDL4
270 216 20 3200
390 6.3 10.5 0.08 312 24 3300 PLF0G391MDL4
560 8 9 0.08 448 7 5200 PLF0G561MCO6
4
8 12
4.6 560 0.08 448 7 5500 PLF0G561MDO1
(0G)
680 8 12 0.08 544 6 6200 PLF0G681MDO1
820 10 13 0.08 656 6 6500 PLF0G821MDO1
10 13
1000 0.08 800 6 6640 PLF0G102MDO1
1200 10 13 0.08 960 8 5600 PLF0G122MDO1
220 6.3 10.5 0.08 277 20 3200 PLF0J221MDL4
6.3 10.5
330 0.08 416 24 3300 PLF0J331MDL4
6.3
470 8 9 0.08 592 7 5200 PLF0J471MCO6
7.2
(0J)
470 8 12 0.08 592 7 5500 PLF0J471MDO1
10 13
680 0.08 857 6 6300 PLF0J681MDO1
47 6.3 10.5 0.08 94 25 2900 PLF1A470MDL4
68 6.3 10.5 0.08 136 25 2900 PLF1A680MDL4
100 6.3 10.5 0.08 200 25 2900 PLF1A101MDL4
150 6.3 10.5 0.08 300 25 2900 PLF1A151MDL4
10
11.5
270 8 12 0.08 540 8 4900 PLF1A271MDO1
(1A)
470 10 13 0.08 940 7 5700 PLF1A471MDO1
560 10 13 0.08 1120 7 5900 PLF1A561MDO1
680 10 13 0.08 1360 7 6100 PLF1A681MDO1
100 6.3 10.5 0.08 320 24 2900 PLF1C101MDL4
180 8 12 0.08 576 9 5000 PLF1C181MDO1
16
270 8 12 0.08 864 9 5100 PLF1C271MDO1
18.4
(1C)
330 10 13 0.08 1056 9 6100 PLF1C331MDO1
470 10 13 0.08 1504 9 6100 PLF1C471MDO1
22 6.3 6 0.12 88 50 1700 PLF1D220MCL2
39 8 7 0.12 156 45 2000 PLF1D390MCL2
47 8 7 0.12 188 45 2000 PLF1D470MCL2
56 10 8 0.12 224 40 2400 PLF1D560MCL2
20
68 10 8 0.12 272 40 2600 PLF1D680MCL2
23
(1D)
82 10 8 0.12 328 40 2600 PLF1D820MCL2
100 8 12 0.12 400 22 3320 PLF1D101MDO2
120 10 10 0.12 480 35 2800 PLF1D121MCL2
150 10 13 0.12 600 20 4320 PLF1D151MDO2
6.8 6.3 6 0.12 85 80 1200 PLF1E6R8MCL2
10 6.3 6 0.12 125 65 1500 PLF1E100MCL7
10 8 7 0.12 125 60 1500 PLF1E100MCL2
25
28.7
(1E)
22 8 7 0.12 275 50 1800 PLF1E220MCL7
47 10 13 0.12 588 30 3000 PLF1E470MDO2
56 10 13 0.12 700 28 3800 PLF1E560MDO2
Rated ripple current (mArms) at 105C 100kHz
No marked, 1 will be put at 12th digit of type numbering system.
Please refer to page 20, 21, 22 about the formed or taped product spec.
: In this case, 2 will be put at 12th digit of type numbering system.
Please refer to page 3 for the minimum order quantity.
: In this case, 4 will be put at 12th digit of type numbering system.
: In this case, 6 will be put at 12th digit of type numbering system.
57
: In this case, 7 will be put at 12th digit of type numbering system.
: In this case, 8 will be put at 12th digit of type numbering system.