ALUMINUM ELECTROLYTIC CAPACITORS Chip Type, Low Impedance UUD Chip type, low impedance temperature range up to +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UWD High Temp reflow UCD Low Impedance Low Impedance UWG UUD Specifications Item Performance Characteristics Category Temperature Range 55 to +105C Voltage Range Rated 6.3 to 50V Rated Capacitance Range 1 to 1500F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes application of rated voltage at 20C, leakage current is not more than 0.01 CV or 3 (A), whichever is greater. Measurement frequency : 120Hz at 20C Rated voltage (V) 6.3 10 16 25 35 50 Tangent of loss angle (tan ) ( ) is 8 over tan (MAX.) 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) Measurement frequency : 120Hz Rated voltage (V) 6.3 10 16 25 35 50 Stability at Low Temperature Z25C / Z+20C Impedance ratio 3 2 2 2 2 2 ZT / Z20 (MAX.) Z55C / Z+20C 5 4 4 3 3 3 The specifications listed at right shall be met Capacitance change Within 30% of the initial capacitance value when the capacitors are restored to 20C after the tan 200% or less than the initial specified value Endurance rated voltage is applied for 5000 hours (2000 Leakage current Less than or equal to the initial specified value hours for D = 4, 5 and 6.3) at 105C. After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within 10% of the initial capacitance value Resistance to soldering maintained at 250C. The capacitors shall meet the characteristic tan Less than or equal to the initial specified value heat requirements listed at right when they are removed from the plate Leakage current Less than or equal to the initial specified value and restored to 20C. Marking Black print on the case top. Chip Type Type numbering system (Example : 16V 22 F) (4 to 6.3) Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Plastic platform U U D 1 C 2 2 0 M C L 1 G S C0.2 0.3 MAX. Series Voltage (C:16V) Package code Configuration D Code Capacitance tolerance (20%) 4 to 6.3 CL Rated capacitance (22F) H L0.3 8 10 NL Lot No. Capacitance Negative Rated voltage (16V) Series name Type (8,10 ) Positive Plastic platform (mm) Voltage (V:35V) C0.2 0.3 MAX. Series D L Trade mark 4 5.8 5 5.8 6.3 5.8 6.3 7.7 8 10 10 10 A 1.8 2.1 2.4 2.4 2.9 3.2 B 4.3 5.3 6.6 6.6 8.3 10.3 C 4.3 5.3 6.6 6.6 8.3 10.3 E 1.0 1.3 2.2 2.2 3.1 4.5 L 5.8 5.8 5.8 7.7 10 10 H L0.5 Lot No. Capacitance H 0.5 to 0.8 0.5 to 0.8 Negative 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Pressure relief vent Voltage V 6.3 10 16 25 35 50 j Code A C E V H Dimension table in next page. 153 A2 A2 22C 100V UD UD D0.5 D0.5 B0.2 B0.2 0.5 MAX. 0.5 MAX. A0.2 E A0.2 A0.2 E A0.2ALUMINUM ELECTROLYTIC CAPACITORS UUD Dimensions V 6.3 10 16 25 35 50 Cap. Code 0J 1A 1C 1E 1V 1H (F) 1 010 4 5.8 5.00 30 2.2 2R2 4 5.8 5.00 30 3.3 3R3 4 5.8 5.00 30 4.7 4R7 4 5.8 1.80 80 5 5.8 1.52 85 10 100 4 5.8 1.80 80 5 5.8 0.76 150 6.3 5.8 0.88 165 15 150 4 5.8 1.80 80 5 5.8 0.76 150 5 5.8 0.76 150 6.3 5.8 0.88 165 22 220 4 5.8 1.80 80 5 5.8 0.76 150 5 5.8 0.76 150 5 5.8 0.76 150 6.3 5.8 0.88 165 27 270 4 5.8 1.80 80 5 5.8 0.76 150 5 5.8 0.76 150 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 7.7 0.68 185 33 330 5 5.8 0.76 150 5 5.8 0.76 150 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 7.7 0.68 185 47 470 5 5.8 0.76 150 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 7.7 0.68 185 56 560 5 5.8 0.76 150 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 7.7 0.34 280 8 10 0.34 300 68 680 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 7.7 0.34 280 8 10 0.34 300 100 101 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 7.7 0.34 280 8 10 0.17 450 8 10 0.34 300 150 151 6.3 5.8 0.44 230 6.3 5.8 0.44 230 6.3 7.7 0.34 280 8 10 0.17 450 8 10 0.17 450 10 10 0.18 670 220 221 6.3 5.8 0.44 230 6.3 7.7 0.34 280 6.3 7.7 0.34 280 8 10 0.17 450 8 10 0.17 450 10 10 0.18 670 330 331 6.3 7.7 0.34 280 8 10 0.17 450 8 10 0.17 450 8 10 0.17 450 10 10 0.09 670 470 471 8 10 0.17 450 0.17 450 8 10 0.17 450 10 10 0.09 670 8 10 680 681 8 10 0.17 450 10 10 0.09 670 10 10 0.09 670 1000 102 8 10 0.17 450 10 10 0.09 670 Rated Case size Impedance D L (mm) ripple 1500 152 10 10 0.09 670 Max. Impedance () at 20C 100kHz, Rated ripple current (mArms) at 105C 100kHz Frequency coefficient of rated ripple current Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more Coefficient 0.35 0.50 0.64 0.83 1.00 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 154