ALUMINUMELECTROLYTICCAPACITORS 6mmL Chip Type, Wide Temperature Range UT series Chip type with load life 2000 hours at +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). Long Life UA Long Life WT UT Higher C/V UX Specifications Item Performance Characteristics Category Temperature Range 55 to +105C Rated Voltage Range 4 to 50V Capacitance Range 0.1 to 100F Rated Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes application of rated voltage, leakage current is not more than 0.01 CV or 3 (A) , whichever is greater. Measurement frequency :120Hz at 20C Rated voltage (V) 4 6.3 10 16 25 35 50 Tangent of loss angle (tan ) tan (MAX.) 0.37 0.28 0.24 0.20 0.16 0.13 0.12 Measurement frequency :120Hz Rated voltage (V) 4 6.3 10 16 25 35 50 Stability at Low Temperature Impedance ratio Z25C / Z+20C 6 3 3 2 2 2 2 ZT / Z20 (MAX.) Z40C / Z+20C 12 8 5 4 3 3 3 Capacitance Within 25% of the initial capacitance value (16V or less) The specifications listed at right shall be met change Within 20% of the initial capacitance value (25V or more) when the capacitors are restored to 20C after Endurance tan 200% or less than the initial specified value the rated voltage is applied for 2000 hours at 105C. Leakage current Less than or equal to the initial specified value After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 Shelf Life clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within 10% of the initial capacitance value Resistance to soldering maintained at 250C. The capacitors shall meet the characteristic tan Less than or equal to the initial specified value heat requirements listed at right when they are removed from the plate Leakage current Less than or equal to the initial specified value and restored to 20C. Marking Black print on the case top. Chip Type Type numbering system (Example : 16V 10 F) Positive 105C Marking 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Positive Capacitance Plastic platform 105C Marking U U T 1 C 1 0 0 M C L 1 G S Lot No. Voltage 0.3MAX. C0.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 (mm) Capacitance Plastic platform D Lot No. 0.3MAX. 4 5 6.3 U U T 1 C 1 0 0 M C L 1 G S Taping code Voltage C0.2 (mm) A 1.8 2.1 2.4 Configuration D 4 5 6.3 Taping code B 4.3 5.3 6.6 A 1.8 2.1 2.4 Capacitance tolerance (20%) Configuration 4.3 5.3 6.6 C B 4.3 5.3 6.6 Rated capacitance (10F) E 1.0 1.3 2.2 Capacitance tolerance (20%) C 4.3 5.3 6.6 Rated voltage (16V) Rated capacitance (10F) E 1.0 1.3 2.2 Negative 0.5 to 0.8 5.80.3 Series name Rated voltage (16V) Voltage mark for 6.3V is 6V . Negative 0.5 to 0.8 Type 5.80.3 Series name Voltage mark for 6.3V is 6V . Type Dimensions V 4 6.3 10 16 25 35 50 Cap.(F) Code 0G 0J 1A 1C 1E 1V 1H 0.1 0R1 4 1.0 0.22 R22 4 2.6 0.33 R33 4 3.2 R47 4 3.8 0.47 010 4 6.2 1 2R2 4 11 2.2 3.3 3R3 4 14 4.7 4R7 4 13 4 15 5 19 10 100 4 18 5 23 5 25 6.3 30 22 220 4 22 4 22 5 27 5 30 6.3 38 6.3 42 33 330 5 30 5 30 5 35 6.3 40 6.3 48 47 470 5 36 5 36 6.3 46 6.3 50 Allowable Rated Case size ripple D (mm) 100 101 6.3 60 6.3 60 6.3 60 ripple Rated ripple current (mArms) at 105C 120Hz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Frequency coefficient of rated ripple current Please select UX(p.154), UJ(p.160) series if high C/V products are Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more required. Please refer to page 3 for the minimum order quantity. Coefficient 0.70 1.00 1.17 1.36 1.50 CAT.8100D A2P A2P 10 10 16V 16V D0.5 D0.5 B0.2 B0.2 0.5MAX. 0.5MAX. E E A0.2 A0.2 A0.2 A0.2