ALUMINUMELECTROLYTICCAPACITORS
5.5mmL Chip Type
WX series
Chip type with 5.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Load life of 2000 hours at 85C.
WT WJ
Compliant to the RoHS directive (2011/65/EU).
High High
Temperature Temp reflow
Bi-polarized
WX WP
Smaller
Specifications
ZS
Item Performance Characteristics
Category Temperature Range
40 to +85C
Rated Voltage Range 4 to 50V
Rated Capacitance Range 0.1 to 330F
Capacitance Tolerance 20% at 120Hz, 20C
Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (A) ,whichever is greater.
Measurement frequency : 120Hz at 20C
Rated voltage (V) 4 6.3 10 16 25 35 50
Tangent of loss angle (tan )
0.35 (0.40) 0.26 (0.30) 0.20 (0.24) 0.16 (0.19) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14)
tan (MAX.) Values in ( ) applicable to WR, 3 case size.
Measurement frequency : 120Hz
Rated voltage (V) 4 6.3 10 16 25 35 50
Stability at Low Temperature
7 4 3 2 2 2
Impedance ratio Z25C / Z+20C 2
ZT / Z20 (MAX.) Z40C / Z+20C 15 8 8 4 4 3 3
The specifications listed at right shall be met
Capacitance change
Within 20% of the initial capacitance value (Within 25% for 4 V and 3,WR series units)
when the capacitors are restored to 20C after
Endurance tan 200% or less than the initial specified value
the rated voltage is applied for 2000 hours at
Leakage Current Less than or equal to the initial specified value
85C.
After storing the capacitors under no load at 85C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
Shelf Life
clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change Within 10% of the initial capacitance value
Resistance to soldering
maintained at 250C. The capacitors shall meet the
tan Less than or equal to the initial specified value
characteristic requirements listed at right when they are
heat
Leakage current Less than or equal to the initial specified value
removed from the plate and restored to 20C.
Marking Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10 F)
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Capacitance
Positive
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Capacitance U W X 1 C 1 0 0 M C L 1 G B
2 Lot No. 1 Voltage Plastic platform
0.3 MAX.
U W X 1 C 1 0 0 M C L 1 G B
2 Lot No. 1 Voltage Plastic platform
C0.2
Taping code
0.3 MAX.
C0.2
Taping code
Size code
Size code
Configuration
D Code
Configuration
Capacitance toleranc (20%) 3 2
D Code
4 to 8 1
Capacitance tolerance (20%) 3 2
Rated capacitance (10F)
+0.1
5.4 4 to 8 1
0.2
Rated capacitance (10F)
Rated voltage (16V)
+0.1
Negative
5.4
0.5 to 0.8
0.2
Rated voltage (16V)
Series name
Negative
0.5 to 0.8
(mm)
Series name
Type
D
3 4 5 6.3 8
(mm)
Type
D
A 1.5 1.8 2.1 2.4 3.3
3 4 5 6.3 8
B 3.3 4.3 5.3 6.6 8.3
A 1.5 1.8 2.1 2.4 3.3
In the case of size 3 in ( ),parentheses, use WX in the 2nd and 3rd
C 3.3 4.3 5.3 6.6 8.3
B 3.3 4.3 5.3 6.6 8.3
digit and put a 2 in the 12th digit of type numbering system.
E 0.8 1.0 1.3 2.2 2.3
C 3.3 4.3 5.3 6.6 8.3
1. Voltage mark for 6.3V is 6V .
E 0.8 1.0 1.3 2.2 2.3
In case of marking for 3 units, V for rated voltage is omitted.
1. Voltage mark for 6.3V is 6V .
2. In case of marking for 3 units, Lot No.is expressed by a digit (month code).
In case of marking for 3 units, V for rated voltage is omitted.
2. In case of marking for 3 units, Lot No.is expressed by a digit (month code).
Dimension table in next page.
CAT.8100D
A2
X2
10
10
16V
16V
D0.5
D0.5
B0.2
B0.2
0.5 MAX.
0.5 MAX.
E
E
A0.2 A0.2
A0.2 A0.2ALUMINUMELECTROLYTICCAPACITORS
WX series
Dimensions
V 4 6.3 10 16 25 35 50
Cap. (F) Code 0G 0J 1A 1C 1E 1V 1H
0.1 0R1 4 (3)
1.0
0.22 R22 4 (3)
2.0
0.33 R33 4 (3)
2.8
0.47 R47 4 (3)
4.0
1 010 4 (3)
8.4(8.0)
2.2 2R2 3 8.4 4 (3)
13 (10)
3.3 3R3 3 10 4
17
4.7 4R7 4 (3) 16 (12) 4 18 5
20 (18)
10 100 4 (3) 23 ( 18) 5 27 (24) 5 29 (24) 6.3
33 (30)
22 220 3 019 4 (3) 28 (21) 5 33 (30) 5 37 (30) 6.3 42 (38) 6.3 46 (39) 8
52 (43)
33 330 4 028 5 37 (34) 5 41 (34) 6.3 49 (44) 6.3 52 (46) 8 62 (53) 8
71
47 470 4 033 5 45 (40) 6.3 52 (47) 6.3 58 (52) 8 70 (60) 8 80
56 560 5 042 6.3 52 (46) 6.3 57 (50) 6.3 63 (57) 8 76 (65)
100 101 5 056 6.3 70 (47) 6.3 76 (54) 6.3 86 8 110
150 151 6.3 079 6.3 71 8 111 (76)
220 221 6.3 096 8 110 (74) 8 135
Rated
Case size
ripple
D (mm)
330 331 8 145 8 170
Rated ripple current (mArms) at 85C 120Hz
( ) is also available with 3mm upon request.
( ) = 3 units and WR Series
In the case of size 3 in ( ),parentheses, use WX at 2nd and 3rd digit and put 2 at the 12th digit of type numbering system.
Size 4 is available for capacitors marked.
Size 5 is available for capacitors marked. In such a case, W R will be put at 2nd and 3rd digit of type numbering system.
}
Size 6.3 is available for capacitors marked.
Frequency coefficient of rated ripple current
Frequency
50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more
Coefficient
0.70 1.00 1.17 1.36 1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UR(p.150), UG(p.158) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100D