NJM2904C / NJM2904CA SINGLE-SUPPLY DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION PACKAGE OUTLINE The NJM2904C / NJM2904CA consists of two independent, high gain, internally frequency compensated operation amplifiers, which were designed specifically to operate from a single power supply over a wide NJM2904CG NJM2904CM range of voltages. Operation from split power supplies is also possible and NJM2904CAG NJM2904CAM the low power supply current drain is independent of the magnitude of the (SOP8) (DMP8) power supply voltage. Application areas include transducer amplifiers, DC gain blocks, and all the conventional op amp circuits, which now can be more easily implemented in single power supply systems. For example, the NJM2904C NJM2904CRB1 NJM2904CV can be directly operated off of the standard +5V power supply voltage, NJM2904CARB1 NJM2904CAV which is used in digital systems and will easily provide the required interface (MSOP8(TVSP8)) (SSOP8) electronics without requiring the additional 15V power supplies. FEATURES NJM2904CME2 Single Supply (EQFN12-E2) Operating Voltage +3V to +32V Low Operating Current 0.7mA typ. Slew Rate 0.6V/s typ. Bipolar Technology Package Outline SOP8, DMP8 ,SSOP8, EQFN12-E2, MSOP8 (TVSP8) **MEET JEDEC MO-187-DA / THIN TYPE Internal ESD protection Human body model (HBM) 2000V typ. Wide temperature range -40 to +125 Input Offset Voltage Grade NJM2904C(Normal-Grade) NJM2904CA(A-Grade) * NJM2904CME2 dont have a A version. 7mV max. 2mV max. PIN CONFIGURATION (Top View) (Bottom View) PIN FUNCTION (Bottom View) (Top View) 1. A OUTPUT (Top View) 12 11 10 10 11 12 PIN FUNCTION 2. A INPUT 1.A OUTPUT 1 8 3. A +INPUT 2.A - INPUT 4. NC A 1 9 - 2 7 3.A + INPUT 9 1 5. V - 4.V 6. NC B 3 6 2 8 8 PAD 2 5.B + INPUT 7. B +INPUT 6.B - INPUT 8. B INPUT 3 7 3 4 5 7 7.B OUTPUT 9. B OUTPUT + 8.V 10. NC + NJM2904CG/2904CAG 11. V 6 5 4 4 5 6 NJM2904CM/2904CAM 12. NC NJM2904CRB1/2904CARB1 NJM2904CME2 (Note1, 2, 3) NJM2904CV/2904CAV (Note1) The PAD have to be wired as short as possible to connect with a V terminal. (Note2) The PAD is electronically connected to the backside of the die. But, there cannot be used as V- pin. (Note3) The NC pin is not internally connected. EQUIVALENT CIRCUIT ( 1/2 Shown ) + V -INPUT +INPUT OUTPUT - V Ver.12 - 1 - NJM2904C / NJM2904CA ABSOLUTE MAXIMUM RATINGS ( Ta=25C ) PARAMETER SYMBOL RATINGS UNIT + - Supply Voltage V - V +32 V Differential Input Voltage (Note4) V 32 V ID - - Input Voltage (Note5) V V - 0.3 to V + 32 V IN - + Output Terminal Input Voltage Vo V - 0.3 to V +0.3 V SOP : 690 (Note6) 1000(Note7) DMP : 470 (Note6) 600 (Note7) Power Dissipation P MSOP : 510 (Note6) 680 (Note7) mW D SSOP : 430 (Note6) 540(Note7) EQFN : 440 (Note8) 680(Note9) Operating Temperature Range T -40 to +125 C opr Storage Temperature Range T -65 to +150 C stg (Note4)Differential voltage is the voltage difference between +INPUT and -INPUT. (Note5) Input voltage is the voltage should be allowed to apply to the input terminal independent of the magnitude of V+. The normal operation will establish when any input is within the Common Mode Input Voltage Range of electrical characteristics. (Note6) EIA/JEDEC STANDARD Test board (76.2 x 114.3 x 1.6mm, 2layers, FR-4) mounting (Note7) EIA/JEDEC STANDARD Test board (76.2 x 114.3 x 1.6mm, 4layers, FR-4) mounting (Note8) EIA/JEDEC STANDARD Test board (101.5 x 114.3 x 1.6mm, 2layers, FR-4) mounting (Note9) EIA/JEDEC STANDARD Test board (101.5 x 114.3 x 1.6mm, 4layers, FR-4) mounting ELECTRICAL CARACTERISTICS + - (V =5V, V =0V, Ta=25C, unless otherwise noted.) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT + V =5V, no signal - 0.7 1.2 Supply Current (All amplifiers) ISUPPLY mA + V =30V, no signal - - 2 R =0 - 0.5 7 S Input Offset Voltage V mV IO R =0 , NJM2904CA - 0.5 2 S Input Bias Current I - 20 150 nA B Input Offset Current I - 2 30 nA IO Open-Loop Voltage Gain A R 2k 94 100 - dB V L + Supply Voltage Rejection Ratio SVR V =5 to 30V,Rs<10k 65 100 - dB Common Mode Input + + V V =30V, CMR>70dB 0 - V -1.5 V ICM Voltage Range Common Mode Rejection Ratio CMR Rs<10k 70 100 - dB + Output Source Current I V =15V,V =+2V, V +=1V, V -=0V 20 40 - mA SOURCE o IN IN + V =15V,V =+2V, V +=0V, V -=1V 10 20 - mA o IN IN Output Sink Current I SINK + V =15V,V =+0.2V, V +=0V, V -=1V 12 50 - A o IN IN + R =2k,V =30V 26 27 - L High-level output voltage V V OH + R =10k,V =30V 27 28 - L Low-level output voltage VOL RL=10k - 5 20 mV + Slew Rate SR V =15V,V =0.5 to 3V,C =100pF - 0.6 - V/s IN L + V =30V,f=100kHz,V =10mVrms,R =2k, IN L Gain Band Width Product GBW - 1.1 - MHz C =100pF L Total Harmonic Distortion + Noise THD+N f=1kHz,G =20dB,R =2k,V =2V ,C =100pF - 0.02 - % v L o pp L + nV/Hz Equivalent input noise voltage e f=1kHz, Rs =100,V =30V - 30 - n Channel Separation CS 1kHz< f <10kHz - 120 - dB Ver.12 - 2 -