RP500L (DFN1616-6) is the limited product, RP500Z (WLCSP-6-P2) is the discontinued product as of February 2021. RP500x SERIES 600mA Step-down DC/DC Converter with Synchronous Rectifier NO.EA-155-111124 OUTLINE The RP500x Series are CMOS-based 600mA step-down DC/DC Converters with synchronous rectifier. Each of these ICs consists of an oscillator, a switching control circuit, a reference voltage unit, an error amplifier, a soft-start circuit, protection circuits, UVLO circuit, switching transistors, and so on. A low ripple, high efficiency step-down DC/DC converter can be easily composed of this IC with only an inductor and capacitors. In terms of the output voltage, since the feedback resistances are built-in, the voltage is fixed internally. 0.1V step output can be set by laser-trim and 1.5% or 24mV tolerance depending on the output voltage is guaranteed. Mode alternative circuit works automatically for improving the efficiency. Considering fixed noise frequency, PWM fixed control type is also available. As protection circuits, the current limit circuit which limits peak current of Lx at each clock cycle, and the latch type protection circuit which works if the term of the over-current condition keeps on a certain time exist. The latch-type protection circuit works to latch an internal driver with keeping it disable. To release the condition of the protection, after disabling this IC with a chip enable circuit, enable it again, or restart this IC with power-on or make the supply voltage at UVLO detector threshold level or lower than UVLO. Since packages are WLCSP-6-P2, DFN1616-6, DFN(PLP)1820-6, SOT-23-6W, high density mounting on boards is possible. )This is an approximate value, because output current depends on conditions and external parts. FEATURES Supply Current ......................................................Typ. 400A (at PWM mode) Typ. 100A (at VFM mode) Standby Current ....................................................Max. 5A Input Voltage Range .............................................2.55V to 5.50V Output Voltage Range...........................................1.1V to 3.3V (0.1V steps) (For other voltages, please refer to MARK INFORMATIONS.) Output Voltage Accuracy.......................................1.5% (VOUT1.6V), 24mV (VOUT<1.6V) Temperature-Drift Coefficient of Output Voltage ...Typ. 100ppm/C Oscillator Frequency.............................................Typ. 1.2MHz Oscillator Maximum Duty Cycle............................Min. 100% Built-in Driver ON Resistance ...............................Typ. Pch. 0.3, Nch. 0.38 (VIN=3.6V) UVLO Detector Threshold.....................................Typ. 2.2V Soft Start Time.......................................................Typ. 120s Lx Current Limit.....................................................Typ. 900mA Latch type Protection Circuit.................................Typ. 1.5ms Two choices of Switching Mode............................Automatic PWM/VFM mode change / PWM fixed Packages..............................................................WLCSP-6-P2, DFN1616-6, DFN(PLP)1820-6, SOT-23-6W APPLICATIONS Power source for battery-powered equipment. Power source for hand-held communication equipment, cameras, VCRs, camcorders. Power source for HDD, portable equipment. 1 RP500L (DFN1616-6) is the limited product, RP500Z (WLCSP-6-P2) is the discontinued product as of February 2021. RP500x BLOCK DIAGRAMS RP500xxx1A/2A VIN Chip Ramp Current CE Enable Compensation Feedback OSC Current LX Protection Vref PWM Switching Control Control Soft Start VOUT UVLO AGND PGND ) only RP500xxx1A for automatic PWM/VFM mode change RP500xxx3A/4A VIN Chip Ramp Current CE Enable Compensation Feedback OSC Current LX Protection Vref PWM Switching Control Control Soft Start VOUT UVLO AGND PGND ) only RP500xxx3A for automatic PWM/VFM mode change 2