RP506K001F012-EV 2 A PWM/VFM Step-down DC/DC Converter with Synchronous Rectifier Evaluation Board NO.EEV-296-012-190517 RP506K001F012-EV is the evaluation board for RP506 which has the below features, benefits and specifications. OUTLINE The RP506K is a low supply current CMOS-based PWM/VFM step-down DC/DC converter with synchronous (1) rectifier featuring 2 A output current. Internally, a single converter consists of an oscillator, a reference voltage unit, an error amplifier, a switching control circuit, a mode control circaui t,s oft start circuit, a latch type protection circuit, an under -voltage lockout (UVLO) circuit, a thermal shutdown circuit, and switching transistors. The RP506K is employing synchronous rectification for improving the efficiency of rectification byr eplacing diodes with built-in switching transistors. Using synchronous rectification not only increases circuit performance but also allows a design to reduce parts count. Power controlling method can be selected from forced PWM control type or PWM/VFM auto switching control type by inputting a signal to the MODE pin. In low output current,f orced PWM control switches at fixed frequency rate in order to reduce noise. Likewise, in low output current, PWM/VFM auto switching control automatically switches from PWM mode to VFM mode in order to achieve high efficiency. Output voltage type can be selected from an internally fixed output voltage type (RP506Kxx1A/B/D/E) or an externally adjustable output voltage type (RP506K001C/F). The output voltage of the RP506Kxx1A/B/D/E can be set by 0.1 V step and the output voltage accuracy is as high as 1.5% or 18 mV. The output voltage of the RP506K001C/F can be set by using the external resistors. Oscillator frequency can be selected from 2.25 MHz (RP506Kxx1A/B/C) or 1.2 MHz (RP506Kxx1D/E/F). Soft- start time is Typ. 0.15 ms, and by connecting an external capacitor to the TSS pin, soft-start time is adjustable. Power good (PG) function monitors the VOUT pin voltage or the feedback pin voltage (VFB), and switches the PG pin to low if any abnormal condition is detected. Protection circuits included in the RP506K are over current protection circuit, latch type protection circuit and thermal shutdown circuit. Over current protection circuit supervises the inductor peak current in each switching cycle, and if the current exceeds the XL current limit (ILXLIM), it turns off Pch Tr. Latch type protection circuit latches the built-in driver to the OFF state and stops the operation of the stepd- own DC/DC converter if the over current status continues or VOUT continues being the half of the setting voltage for equa lor longer than protection delay time (tprot). Thermal shutdown circuit detects overheating of the converter if the output pin is shorted to the ground pin (GND) etc. and stops the converter operation to protect it from damage if the junction temperature exceeds the specified temperature. The RP506K is available in DFN(PLP)2527-10 which achieves high-density mounting on boards. (1) This is an approximate value. The output current is dependent on conditions and external components. 1 RP506K NO.EEV-296-012-190517 FEATURES Supply Current Typ. 48 A (VFM mode, Lx at no load) Standby Current Typ. 0 A Input Voltage Range 2.5 V to 5.5 V (Absolute Maximum Ratings: 6.5 V) Output Voltage Range Adjustable output voltage type (RP506K001F) : to 4.0 V Forced PWM Control PWM/VFM Auto Switching Control Version RP506K001F 0.6 V to 4.0 V (1) Output Voltage Accuracy 1.5% (V 1.2 V) SET 18 mV (V < 1.2 V) (RP506Kxx1A/B/D/E) SET Feedback Voltage Accuracy 9 mV (VFB = 0.6 V) (RP506K001F) Output Voltage/Feedback Voltage Temperature Coefficient 100 ppm/C Oscillator Frequency Typ. 1.2 MHz (RP506Kxx1F) Oscillator Maximum Duty Min. 100% Built-in Driver ON Resistance Typ. Pch. 0.130 , Nch. 0.125 (VIN = 3.6 V) UVLO Detector Threshold Typ. 2.2 V Inductor Current Limit Circuit Current limit Typ. 2.8 A Latch Type Protection Circuit Typ. 1.5 ms Package DFN(PLP)252710 For more details on RP506 IC, please refer to