Series FR02 10mm Ultra-Thin SMT DIP Rotaries General Specifications Electrical Capacity (Resistive Load) Switching Rating: 100mA 5V DC Nonswitching Rating: 100mA 50V DC Other Ratings Contact Resistance: 100 milliohms maximum for circuit 30 milliohms maximum for contact point Insulation Resistance: 1,000 megohms minimum 250V DC Dielectric Strength: 250V AC minimum for 1 minute minimum Mechanical Life: 10,000 detent operations minimum Electrical Life: 10,000 detent operations minimum Notes: A detent operation is one actuator position operation or stepping. A cycle is one 360 rotation. 10,000 detent operations equal 625 cycles for hexadecimal devices or 1,000 cycles for decimal devices. Nominal Operating Torque: 0.008Nm for decimal devices 0.01Nm for hexadecimal devices Contact Timing: Nonshorting Materials & Finishes Actuator: Screwdriver and Plastic Shaft - Glass fiber reinforced polyamide (UL94V-0) Housing & Base: Glass fiber reinforced polyamide (UL94V-0) Leaf Spring: Stainless steel G Movable Contacts: Copper alloy with gold plating Stationary Contacts: Phosphor bronze with gold plating Terminals: Phosphor bronze with gold plating Environmental Data Operating Temperature Range: 25C through +85C (13F through +185F) Humidity: 90 ~ 95% humidity for 240 hours 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Reflow Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Note: During soldering process, set the switch to the following position: FR02FR10P, FR02FR16P, FR02KR10P, FR02KR16P: 0 position FR02FC10P, FR02KC10P: 7 position FR02FC16P, FR02KC16P: F position Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 rated actuator, housing, & base The FR02 Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. G12 www.nkkswitches.com Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles10mm Ultra-Thin SMT DIP Rotaries Series FR02 Distinctive Characteristics Slim .150 (3.8mm) body has the lowest profile in the industry and allows close stacking of PC boards. Highly visible legends and choice of screwdriver or shaft actuators with arrow position indication provide trouble-free code setting. Detent mechanism gives crisp, positive action for accurate switch setting. Use of heat resistant resin allows infrared convection reflow soldering. Gull-winged terminals ensure mechanical stability during soldering and simplify solder joint inspection. Cam activated movable contact and gold contacts assure contact G reliability and continuity. Actual Size Tape-reel packaging meets EIA-481-2 Standard. Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0059 (0.15mm). (Additional co- planarity details in Terms and Acronyms in the Supplement section.) TRUTH TABLES (CIRCUITS & POSITIONS) Actuator Position Decimal Hexadecimal 10 16 x = ON Terminal No. (Output) 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 R Real Coded 2 Model Numbers: 4 FR02FR, FR02KR 8 1 C Complement 2 Coded Model Numbers: 4 FR02FC, FR02KC 8 Terminal numbers are actually on the switch. www.nkkswitches.com G13 Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles