Series HS TS PS Standard Size Rotaries GENERAL SPECIFICATIONS Electrical Capacity Resistive Load: HS13: 6A 125V AC, 3A 250V AC, or 5A 30V DC HS16: 12A 125V AC or 6A 250V AC TS: 6A 125/250V AC PS: 30A 125/250V AC Other Ratings Contact Resistance: 10 milliohms maximum Insulation Resistance: 200 megohms minimum 500V DC Dielectric Strength: 1,500V AC minimum for 1 minute minimum Mechanical Life: HS: 15,000 operations minimum TS: 30,000 operations minimum PS: 10,000 operations minimum Electrical Life: HS: 7,500 operations minimum TS: 10,000 operations minimum PS: 5,000 operations minimum Indexing: 30 for HS16, TS & PS 45 for HS13 Contact Timing: Nonshorting HS13 Shorting & Nonshorting HS16 Nonshorting TS Nonshorting PS Range of Operating Torque: HS16: 0.54 ~ 0.64Nm for first pole & 0.05Nm for each additional pole HS13: 0.15 ~ 0.24Nm TS: 0.09Nm for first pole & (0.07Nm x total number of poles) + 0.13Nm for additional poles PS: 0.14Nm for each pole G Materials & Finishes Knob: Phenolic resin Shaft: HS13: brass HS16, TS, & PS: brass with nickel plating Bushing: HS13: brass HS16, TS, & PS: brass with nickel plating Case: Phenolic resin Movable Contacts: HS13, HS16, & TS phosphor bronze PS silver alloy Stationary Contacts: HS13, HS16, & PS: brass with silver plating TS: phosphor bronze Terminals: HS: phosphor bronze TS & PS: copper with silver plating Environmental Data Operating Temp Range: 10C through +70C (+14F through +158F) Humidity: 90 ~ 98% humidity for 96 hours 40C (104F) Vibration: 10 ~ 55 Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 3 right angled directions, with 3 shocks in each direction) Installation Mounting Torque: 2.94Nm (26 lbin) Maximum Panel Thickness: Shown with panel cutouts in following drawings Soldering Time & Temperature: Manual Soldering (HS series only): See Profile A in Supplement section. Standards & Certifications UL: File No. E44145 - Recognized only when ordered with marking on switch. Add /U or /CUL to end of part number to order UL recognized switch. HS16 models 1 through 6pole are recognized at 12A 125V AC & 6A 250V AC See Supplement section to find UL or cULus rating details. G46 www.nkkswitches.com Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles7 8 9 0 1 1 1 p y 30 T M O 5 4 C 15 Standard Size Rotaries Series HS 6 AMP SINGLE POLE/NONSHORTING/45 INDEXING Schematics Round D-flat Number of Stopper Number of Load Shaft Shaft Positions Settings Terminals Terminals C of Keyway C of Keyway C of Keyway L L L HS13X HS13Y HS13Z 3 3 HS13X HS13X-D 2 Fixed 1 COM, 2 LOAD 1 & 2 2 2 2 4 HS13Y HS13Y-D 3 Fixed 1 COM, 3 LOAD 1, 2, & 3 1 1 1 C C C 1 1 1 HS13Z HS13Z-D 4 Fixed 1 COM, 4 LOAD 1, 2, 3, & 4 Switch is viewed from shaft end and shown in position 1. Terminal numbers are not on switch. Standard Hardware shown on last page of this section. (10.3) Dia (0.7) Typ Keyway M10 P0.75 4 (10.5) Dia .406 .028 3 .413 (9.5) (6.0) Dia .374 (9.0) .236 2 .354 (1.5) .059 (3.0) Dia 1 .118 Maximum Effective Panel Thickness (0.3) (5.7) Typ COM .012 .224 With Locking Ring (10.0) (10.0) (16.0) (4.8) Typ .394 .394 .630 .150 (3.8mm) .189 (40.0) (2.6) Dia Typ (34.0) Dia Without Locking Ring 1.575 .102 1.339 HS13X .189 (4.8mm) 12 AMP/SHORTING & NONSHORTING/30 INDEXING Knurled Shaft D-flat Shaft Number of Stopper Number of Nonshorting Shorting Nonshorting Shorting Pole Positions Settings Terminals Schematic C HS16-1 HS16-1S HS16-1N HS16-1SN 1P 2-11 2, 3, 4 . 11 1 COM, 11 LOAD 1 1 11 2 HS16-2 HS16-2S HS16-2N HS16-2SN 2P 2-11 2, 3, 4 . 11 2 COM, 22 LOAD G 10 3 HS16-3 HS16-3S HS16-3N HS16-3SN 3P 2-11 2, 3, 4 . 11 3 COM, 33 LOAD C of Keyway L HS16-4 HS16-4S HS16-4N HS16-4SN 4P 2-11 2, 3, 4 . 11 4 COM, 44 LOAD 4 9 HS16-5 HS16-5S HS16-5N HS16-5SN 5P 2-11 2, 3, 4 . 11 5 COM, 55 LOAD 5 8 HS16-6 HS16-6S HS16-6N HS16-6SN 6P 2-11 2, 3, 4 . 11 6 COM, 66 LOAD 6 7 Switch is viewed from shaft end and shown in position 1. Terminal numbers are not on switch. Standard Hardware shown on last page of this section. Keyway M10 P0.75 (6.0) Dia .236 (65.0) 2.559 (8.0) Typ (4.4) .315 .173 (10.0) (24.5) .394 .965 (34.5) (0.84) Typ 1.358 .033 (55.0) (44.5) (2.6) Dia Typ (6.24) Typ 2.165 1.752 .102 .246 (54.5) 2.146 (64.5) (10.3) Dia 2.539 (10.5) Dia .406 (15.0) (14.0) (74.5) (7.0) Max .413 .591 .551 2.933 .276 (9.5) .374 (9.0) On each deck of multipole devices common and load terminals .354 (1.5) are in the same positions as shown in the schematic above059 (3.0) Dia .118 Switch is viewed from the shaft end and shown in position 1. Maximum Effective Panel Thickness With Locking Ring Terminal numbers are on the switch bottom. Stopper positions .189 (4.8mm) are molded on the top of the switch. Without Locking Ring .228 (5.8mm) Standard Hardware shown on last page of this section. HS16-2N www.nkkswitches.com G47 1 2 3 Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles 4 5 6