JF15CP2G NKK Switches

Series JF Ultra-Thin Process Sealed Tactiles General Specifications Electrical Capacity (Resistive Load) Low/Logic Level: 50mA 24V DC Other Ratings Contact Resistance: 50 milliohms maximum Insulation Resistance: 500 megohms minimum 250V DC Dielectric Strength: 250V AC minimum for 1 minute minimum Mechanical Life: 500,000 operations minimum Electrical Life: 500,000 operations minimum Nominal Operating Force: 1.96N for sculptured actuator 2.0N for piano actuator 3.0N for square & round flush actuators Total Travel: Flush Actuators .016 (0.4mm) Sculptured & Piano Actuators .031 (0.8mm) Materials & Finishes Actuator: Polyamide Case: Glass fiber reinforced polyamide Seal: Nitrile butadiene rubber Base: Glass fiber reinforced polyester Movable Contact: Phosphor bronze with silver plating Stationary Contacts: Brass with silver plating Terminals: Brass with silver plating Environmental Data Operating Temperature Range: 25C through +85C (13F through +185F) Humidity: 90 ~ 95% humidity for 96 hours 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning J in 1 minute 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Wave Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: Automated cleaning. See Cleaning specifications in Supplement section. Standards & Certifications The JF Series tactiles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. J34 www.nkkswitches.com Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers TogglesUltra-Thin Process Sealed Tactiles Series JF Distinctive Characteristics Extremely low profile of 5mm from PCB to top of switch. Rubber seal construction prevents contact contamination and allows automated soldering and cleaning. Minimal operating force and short stroke permit light touch operation. Dome contact gives crisp tactile and audible feedback to positively indicate circuit transfer and assures high reliability and long life. Wide choice of body shapes and colors. Actual Size Crimped terminals provide a spring type action to ensure secure mounting and prevent dislodging during wave soldering. Space saving body dimensions provide for compact, side-by-side mounting on a standard grid. Terminal spacing conforms to standard .100 (2.54mm) PCB grid. J Common Bus Matrix X-Y Matrix These single pole, single throw switches can be used in a key- These single pole, single throw switches can be board matrix and, using strapped terminals, achieve a com- arranged on a single-sided PC board matrix mon bus electrical configuration on a single-sided PC board. with strapped terminals to achieve an X-Y type electrical interconnection. 5 9 1 2 3 13 1 2 3 PC Terminations PC Terminations 12 34 56 78 9101112 13 12 34 56 7 1 1 1 2 2 4 5 6 10 4 5 6 3 3 4 2 4 4 6 5 5 6 6 7 8 11 9 7 8 9 7 7 8 6 3 8 8 9 9 0 0 12 A 0 B A 0 B A A 7 1 B B = ON = ON 5 4 3 2 7 Red = PCB Trace Black = Switch Circuit www.nkkswitches.com J35 Keys (Switches) Keys (Switches) Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles