Series JW High Inrush 10 & 16 Amp Rockers General Specifications Electrical Capacity (Resistive Load) Power Level: 10A 125/250V AC for JWM & JWMW models 10A 30V DC for JWMW B 16A 125/250V AC for JWL & JWLW models 5A 72V DC for telecommunication applications Other Ratings Contact Resistance: 10 milliohms maximum for JWM & JWMW 20 milliohms maximum for JWL & JWLW Insulation Resistance: 1,000 megohms minimum 500V DC Dielectric Strength: 2,000V AC minimum between contacts for 1 minute minimum 4,000V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 25,000 operations minimum Electrical Life: 25,000 operations minimum Nominal Operating Force: JWM & JWMW Single Pole 3.92N & Double Pole 7.84N JWL Single Pole 5.00N & Double Pole 10.00N JWLW Double Pole 10.00N Angle of Throw: 26 Materials & Finishes Rocker: Polyphenylene ether (UL94V-0) Contacts: JWM & JWMW: Silver alloy with silver plating Housing/Frame & Barrier: Polyamide (UL94V-0) JWL & JWLW: Silver alloy plus copper with Interior Seal for JWM & JWL: Polyphenylene sulfide (UL94V-0) silver plating Case/Base: Melamine (UL94V-0) Terminals: Brass with silver plating Environmental Data Operating Temperature Range: 25C through +70C (13F through +158F) for JWM & JWL 25C through +85C (13F through +185F) for panel seal JWMW & JWLW models Humidity: 90 ~ 95% humidity for 96 hours 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Sealing: IP67 of IEC60529 standard for panel seal JWMW & JWLW models dust resistant inner seal for others Installation Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 for rocker, housing, seal & case/base of JWL, JWM, JWMW & JWLW models TV Ratings for UL & CSA: JWM (TV-5) Overload Test 120V AC for 50 operations: Steady State Current (rms) 7.5A Minimum Inrush Current (peak) 111A. JWM (TV-5) Endurance Test 120V AC for 25,000 operations: Steady State Current (rms) 5A Minimum Inrush Current (peak) 78A. JWL (TV-8) Overload Test 120V AC for 50 operations: Steady State Current (rms) 12A Minimum Inrush Current (peak) 163A. JWL (TV-8) Endurance Test 120V AC for 25,000 operations: Steady State Current (rms) 8A Minimum Inrush Current (peak) 117A. UL: File No. E44145 JWM & JWMW models recognized at 10A 250V AC. JWMW recognized at 10A 30V DC. JWL & JWLW models recognized at 16A 250V AC JWL at 5A 72V DC. Models below recognized only when ordered with marking on switch. JWMW: add /U to end of part number to order UL mark on switch add /CUL to end of part number to order cULus mark on switch. JWL: add /U-DC to end of part number to request UL rating on DC rated switch. CSA: File No. 023535 0 000 JWM & JWMW models certified at 10A 250V AC JWL models certified at 16A 250V AC VDE: License No. 115674 JWM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at 250V AC JWL models approved at steady state inrush 128A, resistive 16A, & motor load 8A all at 250V AC. Note: JWM & JWL Double Pole, Single Throw models approved only with the international ON-OFF symbols on the actuator. B40 www.nkkswitches.com 8/3/17 Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers TogglesHigh Inrush 10 & 16 Amp Rockers Series JW Distinctive Characteristics Industrys first molded rocker with TV rating. Designed to handle large inrush current, B with high electrical capacity of 10 and 16 Amps. JWM models certified for TV-5 rating and JWL models for TV-8 rating. JWMW and JWLW panel seal versions meet IP67 of IEC60529 Standards (similar to NEMA 4 and 6). Prominent external insulating barriers increase insulation resistance and dielectric strength. Uniquely constructed to break light contact welds. Increased electrical life with specially designed plate to minimize contact bounce. Constructed for dust resistance with interior cover between actuator and contact area. Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Solder lug/quick connect terminals can be used with connector. Housing and case of heat resistant resin meet UL94V-0 standard. Actual Size JWM www.nkkswitches.com B41 Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles