M2019TJW01-FA NKK Switches

Series M Miniature Rockers General Specifications Electrical Capacity (Resistive Load) B Power Level (silver): 6A 125V AC & 3A 250V AC 4A 30V DC for On-None-On 3A 30V DC for all other circuits Logic Level (gold): 0.4VA maximum 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A 20mV ~ 28V) Logic/Power Level (gold over silver): Combines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings Contact Resistance: 10 milliohms maximum for silver 20 milliohms maximum for gold Insulation Resistance: 1,000 megohms minimum 500V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum Mechanical Life: 50,000 operations minimum Electrical Life: 25,000 operations minimum for silver 50,000 operations minimum for gold 50,000 operations minimum for silver at 3A 125V AC Angle of Throw: 25 Materials & Finishes Actuator Clip & Mounting Frame: Stainless Steel Body Frame: Stainless steel Case: Diallyl phthalate resin (UL94V0) Movable Contactor: Phosphor bronze with silver or gold plating Movable Contacts: Silver alloy (code W) copper with gold plating (code G) or silver alloy with gold plating (code A) Stationary Contacts: Silver with silver plating (code W) copper or brass with gold plating (code G) or silver with gold plating (code A) Terminals: Copper or brass with silver plating or copper or brass with gold plating Environmental Data Operating Temp Range: 30C through +85C (22F through +185F) Humidity: 90 ~ 95% humidity for 96 hours 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. Manual Soldering for Silver: See Profile B in Supplement section. Note: Actuator must be in OFF (center) position while soldering. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V0 for case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add /U before rfi st dash in part number to order UL recognized switch. All models recognized at 6A 125V AC, 3A 250V AC or 0.4VA maximum 28V DC maximum. CSA: File No. 023535 0 000 - Certified only when ordered with marking on switch. Add /C before rfi st dash in part number to order CSA certified switch. All models certified at 6A 125V AC or 3A 250V AC or 0.4VA maximum 28V maximum. B62 www.nkk.com Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers TogglesMiniature Rockers Series M Distinctive Characteristics B Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PCB. High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. The molded diallyl phthalate case has a UL 94V-0 flammability rating. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Prominent external insulating barriers increase insulation resistance and dielectric strength. Bias guard prevents misalignment of contacts interlocking of actuator block with rocker and internal guide does not allow transmission of diagonal force on rocker to reach contact mechanism. Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength. Actual Size Snap-in Mount Page B64 Bracket PC Mount Page B72 Flat Frame Mount Page B83 www.nkk.com B63 Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles