YB02VA003 NKK Switches

NO IP65 Panel Seal Indicator with Legend YB Indicator YB02VA003 Bushing Mounting Splashproof Dimensions in mm/inch PANEL CUTOUT LEGEND SPECIFICATIONS (9.4) (1.2) x (2.0) Legend RIGHT M16 P1 .370 .047 x .079 Type Style Helvetica Bold NC Type Size 10 Point L - + RIGHT (2.8) COM Legend Color Black .110 Part No. + 0.2 (16.0) Dia 0.0 This Side .630 Laser Etch on Print Method (15.0) Dia (0.5) (7.2) (7.3) (0.5) Typ Inside of Lens .591 .020 .283 .288 .020 Panel Thickness (18.0) Dia (3.0) (5.3) (24.3) (3.7) .020 ~ .197 Legend shown is illustrative only. .709 .118 .209 .957 .146 (0.5mm ~ 5.0mm) Actual art may vary. BASE INDICATOR ROUND CAP AT3005JB (15.0) Dia .591 Round Cap Part Number (12.2) Clear Lens Materials: Polycarbonate (Lens & Insert) .480 White Insert Thermoplastic Elastomer (Seal/Diffuser) YB02WKW01 (4.0) .157 Finish: Glossy ELECTRICAL SPECIFICATIONS FOR LED LED does not come with a resistor Bright LED The electrical specifications shown are determined at a AT628C basic temperature of 25C. If the source voltage exceeds Color Red the rated voltage, a ballast resistor is required. The follow- Maximum Forward Current I 40mA ing diagram and formula will assist in calculating the value FM of the ballast resistor. Typical Forward Current I 26mA F E V R I F + F R = Forward Voltage V 1.9V F I Anode F Maximum Reverse Voltage V 4V Where: R = Resistor Value (Ohms) RM E V F (+) (-) E = Source Voltage (V) Current Reduction Rate Above 25C I 0.50mA/C V = Forward Voltage (V) F F Cathode I = Forward Current (A) F T-1 Bi-pin Ambient Temperature Range 25C ~ +50C Base Indicator Specifications Materials & Finishes Housing/Bezel: Glass fiber reinforced polyamide (UL94V-0) Base: Glass fiber reinforced polyamide (UL94V-0) Lamp Terminals: Phosphor bronze with tin plating Environmental Data Operating Temperature Range: 25C through +50C (13F through +122F) Humidity: 90 ~ 95% humidity for 96 hours @ 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Sealing: IP65 of IEC60529 standard for panel seal models RoHS Compliant: Installation Mounting Torque: 0.785Nm (6.95 lbin) maximum Quick Connect Force: 24.5N maximum downward force on connector Soldering Time & Temperature: Manual Soldering: 390C for 4 seconds, 2 cycles Standards & Certifications Flammability Standards: UL94-0 housing & base www.nkkswitches.com 07/02/18 NOX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Industrial Panel Mount Indicators / Switch Indicators category: Click to view products by NKK Switches manufacturer: Other Similar products are found below : LW1A-P1-W LW1B-A0L 01-152.025 D38999/20FJ29PB L/C 704-6020 704-6026 73.362.4028.0 EUS-704.000.7 750-1520 9001OA120 99-450.837 99-455.837 99-486.837 99-901.9 99-902.9 99-908.0 99-909.4 99-909.5 A0244J1 A3DT-500Y AL6M-P7P-A AOLQW-2B0600 AP1M255-A APD106LN-A APD106LN-G APN1126-G APS122DN-W ATN2100 AYLW4L-A 18-237.035 C0180AANAH HW1A-L1- GD HW1A-P2-GL HW1F-3G HW1R-2DF20-R HW1X-BM411-R HW2A-L1-GL HW2A-P1-GD HW4S-31L HWAZ1N-OB PA2200/1 PA2SHIELD 21-931.2 96-923.5 1625006 99-451.837 99-480.837 99-481.837 99-908.9 99-909.2