QorIQ Multicore Processor Development QorIQ P1010/P1014 Reference Design Board Overview The P1010RDB is a highly integrated reference design board that can help shorten your time to market. The reference design is aimed at low-cost networking applications (with or without trust architecture), wired and wireless access, as well as industrial and smart energy applications. This cost-effective board is based on the QorIQ P1010 processor family and contains leading-edge external components to help you quickly design and implement your target application. The P1010RDB leverages the P1010 processor and supports both the full-featured P1010 as well as the more cost-efficient P1014 device. P1010RDB System Block Diagram P1010RDB System Block Diagram Reset Clocking Power POR Cong CPLD x32 bits DDR3 RJ-11 (1 GB) P1014:16 bits FXS RJ-11 DUAL NAND SLIC Flash (2 GB) Relay QorIQ FXO RJ-11 NOR P1010/ Flash (32 MB) SPI P1014 SPI x1 UTMI iSATA Type A x1 iSATA Header FlexCAN CAN Header PHY x1 Mini-PCIe UART1 6-Lane Header x1 SerDes Mini-PCIe UART0 Micro-AB USB-to-UART x1 SGMII PHY RJ-45 ESDHC SD/MMC x1 SGMII PHY RJ-45 JTAG COP RGMII eTSEC1 RGMII PHY RJ-45 2 I C EEPROM RTC Header DAC VCXO 1588 P1014 not availableThe P1010 processor family is based on Along with the hardware support, the UART the e500 core, built on Power Architecture P1010RDB comes with a board support DUART interface, terminated as RJ45 technology, which has a core frequency package (BSP) that includes both the U-boot connectors range of 5331000 MHz, and supports a and Linux 2.6 operating system support. 32 KB instruction and L1 data cache and a The platform is also available with third-party TDM 256 KB L2 cache. The P1010 also supports software applications. For a demonstration or Two FXS ports connected via na external a complete trust architecture environment, for details of Freescale third-party applications SLIC to the TDM interface CAN controllers for industrial applications, for this platform, please contact your local One FXO port connected via a relay to FXS three Gigabit Ethernet controllers with IEEE Freescale sales office. for switchover to POTS 1588 V2 support, USB 2.0 plus PHY, two PCI P1010RDB Board Features Express 1.0a controllers, up to six SerDes Others interfaces, 16/32-bit DDR3 and DDR3L (16-bit Memory LEDs: Power (green), link (green), activities mode supports ECC), SPI controller supporting 1 GB DDR3 (8-bit x 4 chips), supports up (yellow) booting from SPI, serial flash memory, SD/ to 8 GB on-board DDR3 SDRAM MMC card controller supporting booting from JTAG for debugging flash cards and an integrated security engine. 32 MB (16-bit) NOR flash memory IEEE 1588 V2 signals for test and The new P1010 family with built-in 45 nm 32 MB SLC NAND flash memory measurement process technology provides high integration 2 for cost-efficient solutions and enables a 256 KB I C EEPROM Form Factor trust platform (through trust architecture) for 128 MB SPI flash Mini ITX form factor customers that want to preserve the hardware or software integrity of their platforms. SD/MMC connector to interface with the SD memory card The P1010RDB platform features 1 GB of DDR3 SDRAM, 32 MB NOR flash and PCI Express 32 MB NAND flash, and can boot securely One standard PCI Express connector from either NOR or NAND flash memory. Other boot options (i.e., SD/MMC, SPI) are One mini PCI Express connector also supported. The platform supports three Gigabit-capable ports via an SGMII or RGMII SATA PHYs, as well as a single-port USB and One internal SATA connected to 2.5 160 G associated PHY. SATA 2 HDD The P1010RDB also supports a PCI Express One eSATA connector to rear panel add-in connector and a MiniPCI Express slot, as well as an SD/MMC card slot. These USB 2.0 components, integrated with the P1010 family, One USB 2.0 port connected via UTMI PHY provide an application-specific platform that to mini AB interface can help you get a jump start on your next One USB 2.0 port directly connected to application design. In addition, the P1010RDB mini AB interface provides a simplified migration path for existing PowerQUICC or PowerQUICC Pro Three 10/100/1000 Ports processor customers wishing to migrate to eTSEC 1 connected to RGMII PHY QorIQ multicore processors. Customers can migrate to the single-core P1014 processor as eTSEC 2 and 3 connected to SGMII PHY a stepping stone on their way to a full-featured P1010 processor. Flex CAN Two connectors for field bus interface Since the P1010 product is pin-compatible with the P1014, only one version of the board is available with options on the board support package to target either processor. For more information, please visit freescale.com/QorIQ Freescale, the Freescale logo, PowerQUICC and QorIQ are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. 2011, 2013 Freescale Semiconductor, Inc. Document Number: P1010RDBFS REV 1