PCA9505DGG,112 NXP

PCA9505 9506 2 40-bit I C-bus I/O port with RESET, OE and INT Rev. 5 30 September 2021 Product data sheet 1 General description 2 The PCA9505/PCA9506 provide 40-bit parallel input/output (I/O) port expansion for I C- bus applications organized in 5 banks of 8 I/Os. At 5 V supply voltage, the outputs are capable of sourcing 10 mA and sinking 15 mA with a total package load of 600 mA to allow direct driving of 40 LEDs. Any of the 40 I/O ports can be configured as an input or output. Output ports are totem-pole and their logic state changes at the Acknowledge (bank change). The PCA9505 is identical to the PCA9506 except that it includes 100 k internal pull-up resistors on all the I/Os. The PCA9506 does not include the internal pull- ups on the I/Os to reduce power consumption when used as outputs or when the input is driven by a push-pull driver. The device can be configured to have each input port to be masked in order to prevent it from generating interrupts when its state changes and to have the I/O data logic state to be inverted when read by the system controller. An open-drain interrupt (INT) output pin allows monitoring of the input pins and is asserted each time a change occurs in one or several input ports (unless masked). The Output Enable (OE) pin 3-states any I/O selected as an output and can be used as an input signal to blink or dim LEDs (PWM with frequency > 80 Hz and change duty cycle). The internal Power-On Reset (POR) or hardware reset (RESET) pin initializes the 40 I/ Os as inputs. Three address select pins configure one of 8 target addresses. The PCA9506 is available in 56-pin TSSOP and HVQFN packages, while the PCA9505 is available only in a TSSOP package. They are both specified over the -40 C to +85 C industrial temperature range. 2 Features and benefits 2 Standard mode (100 kHz) and Fast mode (400 kHz) compatible I C-bus serial interface 2.3 V to 5.5 V operation with 5.5 V tolerant I/Os 40 configurable I/O pins that default to inputs at power-up PCA9505 includes 100 k internal pull-up resistors on all the I/Os Outputs: Totem-pole (10 mA source, 15 mA sink) with controlled edge rate output structure Active LOW output enable (OE) input pin 3-states all outputs Output state change on Acknowledge Open-drain active LOW interrupt (INT) output pin allows monitoring of logic level change of pins programmed as inputsNXP Semiconductors PCA9505 9506 2 40-bit I C-bus I/O port with RESET, OE and INT Inputs: Programmable Interrupt Mask Control for input pins that do not require an interrupt when their states change Polarity Inversion register allows inversion of the polarity of the I/O pins when read Active LOW reset (RESET) input pin resets device to power-up default state 3 programmable address pins allowing 8 devices on the same bus Designed for live insertion Minimize line disturbance (I and power-up 3-state) OFF 2 Signal transient rejection (50 ns noise filter and robust I C-bus state machine) Low standby current -40 C to +85 C operation ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 Latch-up testing is done to JEDEC Standard JESD78, which exceeds 100 mA Offered in TSSOP56 (PCA9505, PCA9506) and HVQFN56 (PCA9506) packages 3 Applications Servers RAID systems Industrial control Medical equipment PLCs Cell phones Gaming machines Instrumentation and test measurement PCA9505 9506 All information provided in this document is subject to legal disclaimers. NXP B.V. 2021. All rights reserved. Product data sheet Rev. 5 30 September 2021 2 / 33