TGHD Series Chassis Mounting Non-inductive High Power Resistors Fea TureS 187 Quick connect tabs or fly wire leads Flat type, 100W high power resistor Air-cooled heat sink or water-cooling required. applica TionS Higher density packing, vibration-proof, insulation withstand voltage and perfect Harmonic filter Gate resistor heat dissipation possible. Snubber resistors Dumping resistor for TGHDX contains wire leads and the automotive electronics Surge protection TGHDV contains QC terminals. Power supplies Breeder resistor High frequency ampli- Dummy load fiers cHaracTeriSTicS Derating Rated Power 100W at flange temperature -55 to +100C (wire leads) or -55 to +25C (quick connect) 100 Heat Resistance 0.5C/W from resistor to flange -55 100 80 0.1 to 51k lowest 0.1 ohm is available Resistance Range Nominal Resistance E24+ Modified E24, additionally, 2.0 and 5.0 60 TCR 100 ppm/K (A) For -55 to +155C 40 Tolerance 5% (J) 20 Operation Temp. -55 to +155C at flange element surface 0 E = PR or 1000V Max. Applied Voltage -60 -30 0 30 60 90 120 155 Flange Temperature (C) Withstanding Voltage 5000 VAC 60 seconds, leak current below 0.5mA Torque Mounting 1.6Nm max, 1.0Nm recommend Construction Weight 14g Insulation Resistance Over 1000M between terminals and flange Flange Resistor Substrate Thick film Ni plated Alumina copper ceramics Molding Epoxy Test Procedure Requirement Wire resin Terminals Load Life Continuous power 1000 hours R1.0% Case Humidity 60C, 90 to 95%RH, DC0.1W, 1000 hours R1.0% PA6 Temperature Cycle -55C, 30 min.,+155C 30min., 5 cycles R1.0% resin Vibration IEC60068-2-6, displacement 0.75mm or acceleration R0.5% Tab 100m/sec 2, 10Hz-54Hz sweep, 10 cycles X-Y-Z direction terminals Flammability For resistor body UL94V-0 187tab terminals (continued) 156 1-866-9-OHMITE Intl 1-847-258-0300 Fax 1-847-574-7522 www.ohmite.com info ohmite.com % Rated PowerTGHD Series Chassis Mounting Non-inductive High Power Resistors DimenSionS 19.0 1.0 5.5 .5 14.0 .2 1.5 .2 Tab Terminals Wire Terminals 7.4 .5 (310) 0.75SQ RSU 2-R1.90 10.0 1 3.8+/-0.2 (17.0) 10.5 .2 orDerinG inForma Tion RoHS Compliant Standard part numbers Available values Quick Connect Wired Termination Resistance value is available following TGHDV10R0JE modified E24, +E24. Contact factory for TGHDVR100JE TGHDXR100JE other values. TGHDVR500JE TGHDXR500JE Series Termination Ohm Tolerance TGHDV1R00JE TGHDX1R00JE V = Quick Connect Value J = 5% std. 1.0 1.8 3.0 4.7 7.5 X = Wired TGHDV5R00JE TGHDX5R00JE 1.1 2.0 3.3 5.0 8.0 TGHDV10R0JE TGHDX10R0JE 1.2 2.2 3.6 5.1 8.2 TGHDV27R0JE TGHDX27R0JE 1.3 2.4 3.9 5.6 9.1 TGHDV47R0JE TGHDX47R0JE 1.5 2.5 4.0 6.2 TGHDV100RJE TGHDX100RJE 1.6 2.7 4.3 6.8 TGHDV270RJE TGHDX270RJE TGHDV470RJE TGHDX470RJE TGHDV1K00JE TGHDX1K00JE TGHDV5K00JE TGHDX5K00JE rev 2/21-1 1-866-9-OHMITE Intl 1-847-258-0300 Fax 1-847-574-7522 www.ohmite.com info ohmite.com 157 26.0 .2 24.2 19.0 .5 32.0 .2