Gt h series 120 and 200 Watt SOT227Package Thick Film Power Due to their non-inductive design, these resistors are ideally suited for high-frequency and pulse-load applica- tions. Available in 120- or 200-watt sizes, this resistor is designed for direct mounting onto a heatsink. Popular applications include variable speed drives, power sup- plies, control devices, telecom, robotics, motor controls, and other switching designs. characteristics Nickel-plated copper Heat Sink Derating Contacts Nickel-plated copper Type: H L Substrate Al203 (96%) 100 120 200 Molding Compound High-performance epoxy, compliant to 80 96 160 UL94-V0 60 72 120 American standard 303 stainless steel Terminal Nuts 40 48 80 Resistance Range 0.1 to 1M 20 24 40 Tolerance 5% other tolerances available on request 0 0 0 0 2550 85100 125 150 175 Bottom of base plate Temperature, C Temperature coefficient: 250ppm (at +105C ref. to +25C) Best results can be reached by using a Max. Working Voltage 500V (1000V, not to exceed rated wattage thermal transfer compound with a heat using P*R.) conductivity of better than 1W/mK Power Rating at 85C 120W (see derating) Configurations Partial Discharge up to 2,000Vrms/80 pC (per package) Voltage Proof Dielectric Strength up to 4,000V DC against ground 4 Rth <0.35 K/W Heat Resistance to Cooling Plate 1 2 1 Capacitance/Mass 45pF Config. 1 (V) Config. 2 (X) Working Temp. Range -55C to +155C 3 4 2 50W Max. Torque for Base Plate (static) 1.5 Nm R2 3 4 1 2 R1 1 2 Max. Torque for Contacts (static) 1.3 Nm. M4 screws (not included) Config. 3 (Y) Config. 4 (W) 2.86W/K (0.35K/W) Derating (thermal resistance) Performance Data Test Method R Moisture Resistance MIL-Std-202, Method 106 (0.5% + 0.001W) max Thermal shock Mil-Std-202, Method 107, Cond F (0.3% + 0.01W) max Terminal Strength MIL-Std-202, Method 211, Cond A (pull test) 2.4N (0.2% = 0.01W) max Vibration, High Frequency MIL-Std-202, Method 204, Cond D (0.2% + 0.01W) max Life 20 years (120,000 hours) Operating failure rate of 8.3 x 10-7 fail/hour. Requirements to be achieved under the following conditions: Tamb=25C, THS=70C, Papplied=Pn (continued) 154 1-866-9-OHMITE Intl 1-847-258-0300 Fax 1-847-574-7522 www.ohmite.com info ohmite.com Percent Rated Power Rated Power, WtGh series 120 and 200 Watt SOT227 Package Thick Film Power Dimensions (iin./mm) 1.496 .012 (38mm .3) 0.472 .008 (12mm .2) 1.24 .02 (31.5mm .5) 0.315 .008 0.078 .002 (8mm .2) (2mm .05) 0.031 .002 3 4 (0.8mm .05) 0.157 min. 0.165 .004 (4.0mm) (4.2mm .1) diam. 0.5 .02 0.98 .2 (12.7mm .5) (24.9mm .5) 1 2 0.209 min. (5.3mm) M4 0.59 .008 (15mm 0.2) 0.354 .004 1.189 .004 (9mm .1) (30.2mm .1) orDerinG information Standard Part Numbers Ohms 120 Watt TGHH 200 Watt TGHL Configuration 0.1 TGHHVR100JE TGHLVR100JE V = config. 1 0.5 TGHLVR500JE X = config. 2 1 TGHHV1R00JE TGHLV1R00JE Y = config. 3 Special Option E = RoHS 5 TGHHV5R00JE W = config. 4 A = 1KV compliant 10 TGHHV10R0JE TGHLV10R0JE 25 TGHLV25R0JE TGHLVA25R0JE 33 TGHHV33R0JE TGHLV33R0JE 50 TGHHV50R0JE SOT 227 Series Wattage Resistance Value Tolerance 100 TGHHV100RJE TGHLV100RJE H= 120W Example: J= 5% 150 TGHHV150RJE TGHLV150RJE L= 200W R500 = 0.500 1R00 =1 500 TGHHV500RJE TGHLV500RJE 250R = 250 680 TGHHV680RJE TGHLV680RJE 1K00 = 1,000 1K TGHHV1K00JE TGHLV1K00JE 10K0= 10,000 5K TGHHV5K00JE TGHLV5K00JE 10K TGHHV10K0JE TGHLV10K0JE THIS PRODUCT IS DESIGNED FOR USE WITH PROPER HEATSINKING. Maximum base plate temperature of the resistor must be monitored and kept within specified limits to es- tablish the power rating. Best technique is to attach a thermocouple to the side of the base plate of the resis- tor. Temperature of plastic housing or heat sink cannot be used to establish rating of the resistor. rev 11/21-1 1-866-9-OHMITE Intl 1-847-258-0300 Fax 1-847-574-7522 www.ohmite.com info ohmite.com 155