TGH600 Series 600 Watt Thick Film SOT227 Package Due to the TGH600 s non-inductive design, they are deally suited for high-frequency and pulse- load applications. The TGH600 series resistors are designed for direct mounting onto a heatsink and provides up to 600 watts of power dissipation. Popular applications include variable speed drives, power supplies, control devices, telecom, robotics, motor controls, and other switching designs. cHaracTeriSTicS Ohmic range 0.25 to 1K Derating Resistance tolerance 10% 5% on request 100 600 Temperature coefficient 250ppm/C (others on request) 80 480 Maximum working voltage 1000V DC (higher voltage on request) Power rating 600W at 85C bottom case temperature. Note: 60 360 Liquid cooling required to achieve full power rating. 40 240 Electric strength voltage Dielectric strength up to 4,000VDC against ground 20 120 Isolation voltage between R1 and R2: 500V 1,000V on request 0 0 Partial discharge 2kVrms, <80pC 0525 0 85100 125 150 175 Bottom of base plate Temperature, C 10G min. at 1kV Insulation resistance Derating (thermal resistance): 8.33 W/K (0.12 K/W) Short time overload 1.25 x rated power at 85C bottom case temp. for (for conf. 1, 2, 3) Best results can be obtained by using a thermal transfer compound with a heat con- 10 sec, R = 0.4% max. ductivity of at least 2.9 W/mK. The flatness of the cooling plate must be better than 0.05 mm overall. Operating temperature -55C to +155C Surface roughness should not exceed 6.4 m. Mtg. torque for base plate (static) 1.3 Nm to 1.5 Nm M4 screws (static) 1.1 Nm to 1.3 Nm M4 screws, screw-in Mtg. torque for contacts Configurations depth max. 5mm (per package) Config. 1 (V) Config. 2 (X) Config. 3 (Y) 3 4 4 1 2 1 1 2 Performance Da Ta Test Method R Moisture Resistance MIL-Std-202, Method 106 (0.5% + 0.001W) max Thermal shock Mil-Std-202, Method 107, Cond F (0.3% + 0.01W) max Terminal Strength MIL-Std-202, Method 211, Cond A (pull test) 2.4N (0.2% = 0.01W) max Vibration, High Frequency MIL-Std-202, Method 204, Cond D (0.2% + 0.01W) max Life 20 years (120,000 hours) Operating failure rate of 8.3 x 10-7 fail/hour. Requirements to be achieved under the following conditions: Tamb=25C, THS=70C, Papplied=Pn (continued) 156 1-866-9-OHMITE Intl 1-847-258-0300 Fax 1-847-574-7522 www.ohmite.com info ohmite.com Percent Rated Power Rated Power, WTGH600 Series 600 Watt Thick Film SOT227 Package DimenSionS 1.496 .012 (38mm .3) 0.472 .008 (12mm .2) 1.24 .02 (31.5mm .5) 0.315 .008 0.078 .002 (8mm .2) (2mm .05) 0.031 .002 3 4 (0.8mm .05) 0.157 min. 0.165 .004 (4.0mm) (4.2mm .1) diam. 0.5 .02 0.98 .2 (12.7mm .5) (24.9mm .5) 1 2 0.209 min. (5.3mm) M4 0.59 .008 (15mm 0.2) 0.354 .004 1.189 .004 (9mm .1) (30.2mm .1) orDerinG informa Tion Configuration Standard part numbers V = config. 1 X = config. 2 E = RoHS TGHPVR500KE TGHPV68R0KE Y = config. 3 compliant TGHPV1R00KE TGHPV100RKE TGHPV5R00KE TGHPV150RKE TGHPV7R50KE TGHPV250RKE TGHPV50R0KE TGHPV10R0KE TGHPV470RKE TGHPV15R0KE TGHPV750RKE SOT227 Series Wattage Resistance Value Tolerance TGHPV27R0KE TGHPV1K00KE J= 5% Example: P= 600W TGHPV50R0KE K= 10% R500 = 0.500 1R00 = 1 250R = 250 1K00 = 1,000 10K0 = 10,000 THIS PRODUCT IS DESIGNED FOR USE WITH PROPER HEATSINKING. Maximum base plate temperature of the resistor must be monitored and kept within specified limits to es- tablish the power rating. Best technique is to attach a thermocouple to the side of the base plate of the resis- tor. Temperature of plastic housing or heat sink cannot be used to establish rating of the resistor. rev 11/20-1 1-866-9-OHMITE Intl 1-847-258-0300 Fax 1-847-574-7522 www.ohmite.com info ohmite.com 157