J-7-V3 Omron

J Ultra Subminiature Basic Switch Subminiature Models Capable of Large-capacity load of 7A Snap-action switch allows large-capacity switching (7A at 250 VAC) in spite of its small J size. Particularly suitable as control switches for applications where there are restrictions on installation space and weight. RoHS Compliant Model Number Legend Contact Form SPDT 1 J-7- 1. Actuator None : Pin plunger V : Short hinge lever COM NO NC V22 : Short hinge roller lever V2 : Hinge roller lever Contact Specifications V3 : Hinge lever V4 : Long hinge lever Specification Rivet Contact Material Silver alloy + Gold plated List of Models Gap (standard value) 0.35 mm Minimum applicable load (reference value) 5 VDC 1 mA Actuator Model Pin plunger J-7 Ratings Short hinge lever J-7-V Rated voltage Resistive load 125 VAC 7 A Short hinge roller lever J-7-V22 250 VAC 7 A Note. The above rating values apply under the following test conditions. Hinge roller lever J-7-V2 (1) Ambient temperature: 202C (2) Ambient humidity: 655% Hinge lever J-7-V3 (3) Operating frequency: 30 operations/min Long Hinge Lever J-7-V4 Approved Safety Standards Note. Consult your OMRON sales representative for specific models with safety Consult your OMRON sales representative for specific standard approvals. models with safety standard approvals. UL (UL508)/CSA (CSA C22.2 No.55) Rated voltage Model J-7 125 VAC 7 A 250 VAC 7 A 1J Subminiature Basic Switch Characteristics Permissible operating speed 0.05 mm to 1 m/s (for pin plunger models) Mechanical 400 operations/min max. Permissible operating frequency Electrical 30 operations/min max. Insulation resistance 100 m min. (at 500 VDC with insulation tester) Contact resistance (initial value) 15 m max. Between terminals of the same polarity 600 VAC 50/60 Hz for 1 min Dielectric strength Between current-carrying metal parts and ground 1,500 VAC 50/60 Hz for 1 min Between each terminals and non-current-carrying metal parts 1,500 VAC 50/60 Hz for 1 min J Vibration resistance *1 Malfunction 10 to 55 Hz, 1.5 mm double amplitude 2 Durability 1,000 m/s max. Shock resistance *1 2 Malfunction 200 m/s max. (pin plunger models) Mechanical 10,000,000 operations min. (60 operations/min) Durability *2 Electrical 50,000 operations min. (30 operations/min) Degree of protection IEC IP40 -10C to +80C (at ambient humidity of 60% max.) Ambient operating temperature (with no icing or condensation) Ambient operating humidity 85% max. (for +5C to +35C) Weight Approx. 1 g (pin plunger models) Note. The data given above are initial values. *1. For the pin plunger models, the above values apply for use at the free position, operating position, and total travel position. For the lever models, they apply for the total travel position. Close or open circuit of the contact is shorter than 1 ms. *2. For testing conditions, consult your OMRON sales representative. Dimensions (Unit: mm) and Operating Characteristics 3.5 dia. Pin Plunger 1.5 dia.1.5 dia.1.5 dia. J-7 A PT R0.8 Models Operating Characteristics J-7 Operating Force OF Max. 1.37 N 140 gf Releasing Force RF Min. 0.27 N 28 gf OP Pretravel PT Max. 0.6 mm 8.9 Overtravel OT Min. 0.1 mm 2.3 Movement Differential MD Max. 0.15 mm 5.1 +0.05 2.35 -0.025 Operating Position OP 8.10.3 mm ++0.05 0.05 0.05 2.52.52.5 dia. dia. dia. -0.025-0.025-0.025 1 dia. 3.95 +0.05 1.5 dia. 2.35 dia. 0.05 -0.025 4.8 12.7 0.1 5.1 Short Hinge Lever 9.3 A t=0.3* PT J-7-V 2.3 R12.70.4 Models J-7-V Operating Characteristics Operating Force OF Max. 0.49 N 50 gf Releasing Force RF Min. 0.09 N 9 g 0.4 9.15 8 OP Pretravel PT Max. 1.7 mm 6.6 Overtravel OT Min. 0.35 mm 2.3 Movement Differential MD Max. 0.5 mm 5.1 +0.05 2.35 Operating Position OP 8.31.2 mm -0.025 +0.05+0.05+0.05 2.52.5 2.5 dia. dia. dia. -0.025-0.025 -0.025 1 dia. 3.95 1.5 dia. +0.05 2.35 dia. -0.025 0.05 4.8 12.7 0.1 5.1 14.7 * Stainless-steel lever t=0.3* A PT Hinge Lever 9.3 2.3 0.4 R22 J-7-V3 Models Operating Characteristics J-7-V3 Operating Force OF Max. 0.29 N 30 gf 9.150.4 OP 8 Releasing Force RF Min. 0.05 N 5 gf 6.6 Pretravel PT Max. 2.9 mm 2.3 Overtravel OT Min. 0.5 mm 5.1 +0.05 Movement Differential MD Max. 0.7 mm 2.35 -0.025 ++0.050.050.05 2.52.52.5 dia. dia. dia. -0.025-0.025-0.025 Operating Position OP 8.31.9 mm 1 dia. 3.95 1.5 dia. +0.05 2.35 dia. -0.025 4.80.05 12.7 5.10.1 14.7 * Stainless-steel lever Note 1. Unless otherwise specified, a tolerance of 0.2 mm applies to all dimensions. Note 2. The operating characteristics are for operation in the A direction ( ). 2