Doc No. TA4-EA-05276
Revision. 4
Product Standards
AN33013UA
VIN = 5 to 25 V, VOUT = 1.2 to 22 V, 1-channel DC-DC Step
down Regulator integrated N-channel Power MOSFET
FEATURES DESCRIPTION
1-channel DC-DC Step Down Regulator Circuit that AN33013UA is 1-channel DC-DC Step down Regulator
integrated N-channel Power MOSFET and employs the
employs Voltage Mode Switching Control System
voltage mode switching control system.
Internal reference voltage is within 2% accuracy
This IC can be operated with wide input voltage range
Input Voltage Range : PVCC,VCC: 5 V ~ 25 V
and is build in several protection functions, so this IC can
Adjustable Output Voltage Range with external
provide high reliability power supply system.
Resistor : 1.2 V ~ 22 V (Note)
Since it is possible to use up to 2 MHz switching
Adjustable Switching Frequency with external
frequency and it is unnecessary to add external parts for
Resistor : 200 kHz ~ 2 MHz
High Side Switch, this IC realizes downsizing of set and
Standby mode consumes less than 1 A current
reducing in the number of external parts.
Output over voltage protection (OVP1) function
Output voltage is adjustable by user.
Output ground short protection function
Maximum current is 1.5 A.
Input over voltage protection (OVP2) function
Over current protection with adjustable threshold
APPLICATIONS
Under voltage lockout function (UVLO)
High Input Voltage Power Systems such as
Thermal Shut Down (TSD) function
Car-Audio system
Adjustable soft-start function
Car-Navigation system
SSOP024-P-0300F
OA Equipment
( Size : 8.1 mm X 7.8 mm, 0.65 mm pitch ),
Home Appliances etc.
24pin Plastic Shrink Small Outline Package (SSOP
Type)
(Note) F=490kHz. Please refer Page 10
SIMPLIFIED APPLICATION
PVIN
EFFICIENCY CURVE
Pull-up
100
90
22F3
EN BTVCC VCC
200k
VCC_S
80
FLAG
30m
70
VREG
1.0F RS
60
PVCC1/2
50
SYNC
BT
AN33013UA
0.1F
40
CT
10H VCC=6V
DC-DCOUT
0.1F
RT 30
VCC=12V
LX1/2
SS
VCC=25V
20
TL
22F
130k
TL_CTRL
10
SGND PGND FB COMP
24pF 0
0.1F
0 300 600 900 1200 1500
Iload (mA)
7.5k 2.2nF
0.1F
470pF Condition )
1.5k
Vin = 6 , 12 , 25 V, Vout = 5 V,
30k
7.5k
Lo = 10 H, Co = 22 F, Frequency = 490 kHz
Notes) This application circuit is an example. The operation of
mass production set is not guaranteed. You should
perform enough evaluation and verification on the design
of mass production set. You are fully responsible for the
incorporation of the above application circuit and
information in the design of your equipment.
Page 1 of 18
Established : 2010-09-07
Revised : 2013-06-18
Efficiency (%)Doc No. TA4-EA-05276
Revision. 4
Product Standards
AN33013UA
ABSOLUTE MAXIMUM RATINGS
Parameter Symbol Rating Unit Notes
Supply voltage Vcc 40 V *1
Operating free-air temperature T 40 to + 85 C *2
opr
Operating junction temperature T 40 to + 150 C *2
j
Storage temperature T 55 to + 150 C *2
stg
*1
V , V (Vcc5.5) to (Vcc+0.3) V
CC_S RS
*3
*1
V -0.3 to (Vcc+V ) V
BT REG
*4
Input Voltage Range
*1
V -0.3 to (Vcc+0.3) V
EN
*5
V , V , V , V , V ,
RT TL SS FB BTVCC
-0.3 to 5.5 V *1
V , V
TL_CTRL SYNC
V , V , V -0.3 to 5.5 V *1
FLAG COMP CT
Output Voltage Range
*1
V , V 0.3 to ( Vcc+0.3 ) V
LX1 LX2
*5
HBM (Human Body Model) 2 kV
ESD
MM (Machine Model) 200 V
Notes) Do not apply external currents and voltages to any pin not specifically mentioned.
This product may sustain permanent damage if subjected to conditions higher than the above stated absolute maximum rating.
This rating is the maximum rating and device operating at this range is not guaranteeable as it is higher than our stated
recommended operating range. When subjected under the absolute maximum rating for a long time, the reliability of the product
may be affected.
Vcc is voltage for VCC, PVCC1 and PVCC2. VCC = PVCC1 = PVCC2.
*1:The values under the condition not exceeding the above absolute maximum ratings and the power dissipation.
*2:Except for the power dissipation, operating ambient temperature, and storage temperature, all ratings are for Ta = 25 C.
*3:( Vcc 5.5 ) V must not be exceeded 0.3 V, and ( Vcc + 0.3 ) V must not be exceeded 40 V
*4:( Vcc + V ) V must not be exceeded 40 V
REG
*5:( Vcc + 0.3 ) V must not be exceeded 40 V
POWER DISSIPATION RATING
PACKAGE PD ( Ta = 25 C) PD ( Ta = 85 C) Notes
j-a j-C
24 Pin Plastic Shrink Small Outline Package
135.1 C / W 11.8 C / W 0.925 W 0.481 W *1
(SSOP Type)
Note). For the actual usage, please refer to the PD-Ta characteristics diagram in the package specification, follow the power supply
voltage, load and ambient temperature conditions to ensure that there is enough margin and the thermal design does not
exceed the allowable value.
*1:Glass Epoxy Substrate(1 Layers) [Glass-Epoxy: 50 X 50 X 0.8t(mm)]
CAUTION
Although this has limited built-in ESD protection circuit, but permanent damage may occur on it.
Therefore, proper ESD precautions are recommended to avoid electrostatic damage to the MOS gates
Page 2 of 18
Established : 2010-09-07
Revised : 2013-06-18