Automation Controls Catalog SUBMINIATURE, TURQUOISE STROKE LONG STROKE SEALED SWITCHES MINI SWITCHES FEATURES TYPICAL APPLICATIONS Miniaturization achieved with Automobiles (detection of door 8.3 (Unit: mm) 5.3 changing from 1 Form C to 1 Form A opening and closing, shift lever or 1 Form B contacts. position, etc.) 7.85 (For the terminal type, volume has Household appliances (vacuum been cut 45% compared to our cleaners, air conditioners, washing 8.3 previous product.) machines, etc.) 5.3 Lever installation possible while being miniature. Terminal type 13.55 Operation possible in various moving parts such as metal cams. Contact pressure does not depend on the operation stroke. High contact reliability to support low level switching loads. Highly effective sealing for resis- Wire leads type tance against adverse environments. (IP67) RoHS compliant Silent operation with sliding contact. ORDERING INFORMATION ASQM1 Mounting 1: Without boss type (wire leads type only) 6: Right 2 boss type (terminal type only) 7: Left 2 boss type (terminal type only) Terminal 4: Terminal type (Solder terminal) 6: Wire leads type Contact form 2: Normally Closed type (NC) 3: Normally Open type (NO) Actuator 0: Pin plunger 8: Simulated roller lever Note: Not every combination is available. Please refer to the following table, PRODUCT TYPES. PRODUCT TYPES 1. Terminal type (solder terminal) Carton: 1,000 pcs. Right 2 boss type Left 2 boss type Actuator NC type NO type NC type NO type Pin plunger ASQM16420 ASQM16430 ASQM17420 ASQM17430 Simulated roller lever ASQM16428 ASQM16438 ASQM17428 ASQM17438 2. Wire leads type Carton: 240 pcs. Actuator NC type NO type Pin plunger ASQM11620 ASQM11630 Simulated roller lever ASQM11628 ASQM11638 industrial.panasonic.com/ac/e/ Panasonic Corporation 2013 AECTB55E 201311-T 2013.11 1 NewTurquoise Stroke mini Switch RATING 1. Rating 1 mA, 5 V DC to 50 mA, 16 V DC 2. Operation environment and conditions Item Specications Ambient and storage temperature 40C to +85C (no freezing and condensing) Allowable operating speed 30 to 500 mm/sec. Max. operating cycle rate 120 cpm Note: When switching at low and high speeds or under vibration, or in high-temperature, high-humidity environments, life and performance may be reduced signicantly depending on the load capacity. Please consult us. 3. Electrical characteristics Item Specications Between non-continuous terminals: 500 Vrms, Between each terminal and other exposed metal parts: 1,500 Vrms, Withstand voltage (Initial) Between each terminal and ground: 1,500 Vrms (at detection current of 1 mA) Insulation resistance (Initial) Min. 100 M (at 500 V DC insulation resistance meter) (Locations measured same as withstand voltage.) Contact resistance (Initial) Max. 500 m (By voltage drop 50 mA 6 to 8 V DC) 4. Characteristics Item Specications 5 5 V DC 1 mA (resistive load) Min. 3 10 Switching frequency: 20 times/min. Electrical Conduction ratio: 1:1 5 12 V DC 50 mA (resistive load) Min. 2 10 switching life Plunger operation speed: 100 mm/s 5 16 V DC 50 mA (resistive load) Min. 1.5 10 Plunger switching position: Free Position (F.P.) to Total Travel Position (T.T.P.) Single amplitude: 0.75 mm Amplitude of vibration: 10 to 55 Hz (4 minutes cycle) Direction and time: 30 minutes each in X, Y and Z directions Vibration resistance (malfunction vibration resistance) Amplitude of vibration: 5 to 200 Hz (10 minutes cycle) 2 Acceleration: 43.1 m/s Direction and time: 30 minutes each in X, Y and Z directions 2 Shock resistance Shock value: 980 m/s (malfunction shock resistance) Direction and time: 5 times each in X, Y and Z directions Terminal strength 6 N min. (each direction) *Terminal deformation possible. Heat resistance 85C 500 hours Cold resistance 40C 500 hours Humidity resistance 40C 95% RH 500 hours Water resistance IP67 (Wire leads type) Notes: As long as there are no particular designations, the following conditions apply to the test environment. Ambient temperature: 5 to 35C Relative humidity: 25 to 85% RH Air pressure: 86 to 106 kPa 5. Protective structure 1) JIS C0920 (water-resistance experiments for electrical 3) JIS D0203 (method for testing moisture resistance and water machines and protection rating against incursion of solid resistance in automotive components): Equivalent of D2 (Note 2) substances): Immersion protected (Note 1) Note 1) A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes under 1 m of water (with 2) IEC 60529 (rating for outer shell protection): IP67 (Immersion temperature difference between water and switch no larger than 5C). protected) (Note 1) Note 2) A concrete testing method is to check for any adverse effect on the structure except metal terminal part (See below drawing) after leaving it submerged for 10 minutes under 10 cm water (with temperature difference between water and switch no larger than 30C). Metal terminal part Panasonic Corporation Automation Controls Buisiness Division Panasonic Corporation 2013 AECTB55E 201311-T industrial.panasonic.com/ac/e/ 2