EXB-D10C824J Panasonic

Chip Resistors Networks EXB type EXB D, E, A, Q series Features High density placing for digital signal circuits Bussed 8 or 15 resistors for pull up/down circuits EXBD : 3.2 mm 1.6 mm 0.55 mm, 0.635 mm pitch EXBE : 4.0 mm 2.1 mm 0.55 mm0.8 mm pitch EXBA : 6.4 mm 3.1 mm 0.55 mm1.27 mm pitch EXBQ : 3.8 mm 1.6 mm 0.45 mm0.5 mm pitch Available direct placing on the bus line by means of half pitch spacing without through-holes on PWB (High density placing is shown below) High speed mounting using conventional placing machine Reference Standard : IEC 60115-9, JIS C 5201-9, EIAJ RC-2130 RoHS compliant High density placing Direct placement on the bus line Pull up resistors EXBE10C EXBA10P Vcc Vcc Vcc IC IC IC IC IC IC No through hole Through holes 0.4 mm pitch 0.635 mm pitch As for packaging methods, land pattern, soldering conditions and safety precautions, please see data files. Explanation of part numbers 1T ERJS02 ERJS1T 1 2 3 4 5 6 7 9 10 11 12 8 E X B E 1 0 C 1 0 3 J Suffix for special requirements Product code Resistance tolerance Circuit configuration Resistance value Dimension code of Number of chip resistor network terminals Code Common terminal position Code Tolerance Thick Film 10 Resistor Code Inch Dimensions J 5 Center common circuit The first two C Networks Terminals (EXBD,EXBE) D 1206 3.2 1.6 mm digits are (EXBD) significant figures E 1608 4.0 2.1 mm Diagonal common circuit (Terminal 5 (EXBE) P of resistance and Terminal 10) (EXBA) 6.4 3.1 mm A 2512 (EXBA) value and the 16 Q 1506 3.8 1.6 mm One side common circuit third one denotes Terminals P (Terminal 16) (EXBQ) the number of (EXBQ) zeros following. Diagonal common circuit (Terminal 1 E and Terminal 6) (EXBA) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 1-Mar-20Chip Resistors Networks Ratings Power Limiting Maximum Category AEC- Resistance Resistance *1 element overload T.C.R. Part No. Number of Number of rating temperature range tolerance Q200 *2 *3 -6 (inch size) terminals resistors (70 ) voltage voltage range (10 /K) () (%) Grade (W/element) (V) (V) () EXBD 0.05 / 25 50 200 55 to +125 - (1206) element EXBE 47 to 1 M 10 0.063 / 8 element 25 50 200 55 to +125 - (1608) (E12) terminals element 5 EXBA 0.063 / 50 100 200 55 to +125 - (2512) element EXBQ 100 to 470 k 16 0.025 / 15 element 25 50 200 55 to +125 - (1506) (E6) terminals element *1: Use it on the condition that the case temperature is below the upper category temperature. *2: Rated Continuous Working Voltage (RCWV) shall be determined from RCWV=Power Rating Resistance Value, or Limiting Element Voltage listed above, whichever less. *3: Overload Test Voltage (OTV) shall be determined from OTV=Specified Magnification (refer to performance) RCWV or Maximum Overload Voltage listed above, whichever less. -55 70 Power derating curve 100 80 For resistors operated in ambient temperatures 60 above 70 , power rating shall be derated in accordance with the figure on the right. 40 20 125 0 -40 -20 0 20 60 80 100 120 140 160 180 -60 40 Ambient temperature () Construction(Example : EXBD) Protective coating Protective coating Electrode (Inner) Alumina substrate Electrode (Outer) Thick lm Thick lm resistive element Electrode Alumina substrate resistive element Electrode (Between) (Inner) Circuit configuration EXBD, EXBE EXBA EXBQ EXBA10P EXBA10E 10 9 8 7 6 10 9 8 7 6 10 9 8 7 16 15 14 13 12 11 10 9 1 6 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 7 8 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 1-Mar-20 Rated load (%)