TTSL6VC3-2.5 Panduit

18900 Panduit Drive TDS: GMV17 Tinley Park, IL 60487 Effective Date: 23APR13 Customer Service: 800-777-3300 Revision: 8 Technical Data Sheet Self-Laminating Translucent Vinyl Film This specification is intended to outline the physical properties of PANDUITs pressure sensitive self-laminating translucent vinyl material and include the following part numbers and printable material identifiers: Part Number Prefixes Printable Material Suffixes TTSL TTSL*VC3-*-Y VA1Y V*TY PRODUCT SPECIFICATIONS: Description: Material is RoHS compliant (European Union directive 2002/95/EC). Material is a top coated vinyl film with a pressure sensitive adhesive. This material is used in a self-laminating format for wire/cable marking. Print Methods: This material is recommended for thermal transfer printing. Adhesive: Acrylic based, pressure sensitive adhesive. Standard Colors: Translucent film with colored print-on area Thickness: 4.25 +/- 0.45 mils (substrate and adhesive) Service Temperature Range: -40F to 150F (-40C to 66C) Minimum Application Temperature: 40F (4.4C) Storage Conditions: Store at 70F (21C) and 50% Relative Humidity. PROPERTIES: PERFORMANCE: Peel Adhesion to Stainless Steel: 32 oz/in width (PSTC-101, 15 min. dwell) 45 oz/in width (PSTC-101, 24 hrs dwell) Shear Adhesion: 24+ hours (PSTC-107, Procedure A) Tensile Strength: MD 3200 psi minimum (ASTM D882) 12.2 lbs./inch width minimum (PSTC-131) MD 150% minimum (ASTM D882) Elongation: 150% minimum (PSCT-131) UV Resistance: *3000 hours no change observed (ASTM G154) Elevated Temperature Exposure: After 8 hours at 150F (65.5C) there was no deterioration of the Substrate. Dielectric Strength: 1900 Volts/MIL (ASTM D-149-97, Method A) *3000 hours equates to 5 years of assimilated outdoor UV exposure. Page 1 of 3 2011 PANDUIT Corp TDS: GMV17 18900 Panduit Drive TDS: GMV17 Tinley Park, IL 60487 Effective Date: 23APR13 Customer Service: 800-777-3300 Revision: 8 Technical Data Sheet CHEMICAL/SOLVENT RESISTANCE: Samples were thermal transfer printed with RMR*BL/RMER*BL and RMH*BL/RMEH*BL ribbon. These samples were wrapped around a 1/12 OD wire in self-laminating format. Test was conducted at room temperature after 24 hour dwell. The samples were immersed in the specified chemical reagents for 5 immersions using the following cycle: a 10 minute immersion time followed by a 30 minute recovery time. Visual Observation Chemical Reagent Substrate / Adhesive Thermal Transfer Printed Legend Distilled Water No effect No effect Mineral Spirits No effect No effect ASTM 3 Oil Slight adhesive bleed No effect Isopropyl Alcohol No effect No effect Methanol No effect No effect 3% Alconox Detergent No effect No effect 10% Sodium No effect No effect Hydroxide Solution 10% Sulfuric Acid No effect No effect Solution 5% Sodium Chloride No effect No effect Solution Freon TF No effect No effect Super Agitene No effect No effect Jet-A Fuel Slight adhesive bleed No effect Arco TruSlide 68 No effect No effect SAE 30 Motor Oil No effect No effect Ethanol No effect No effect Bleach No effect No effect Gasoline No effect No effect Ethylene Glycol No effect No effect Approvals UL recognized: UL969 File Number: MH14979 CUL recognized: C22.2 No. 0.15-01 File Number: MH14979 Page 2 of 3 2011 PANDUIT Corp TDS: GMV17