L3GD20H 3-Axis Gyro Carrier with Voltage Regulator Overview This board is a compact (0.4 0.9 ) breakout board for STs L3GD20H three-axis digital-output gyroscope we therefore recommend careful reading of the L3GD20H datasheet (3MB pdf) before using this product. The L3GD20H is a great IC, but its small, leadless, LGA package makes it difficult for the typical student or hoyist to use. It also operates at voltages below 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. This carrier board addresses these issues by incorporating additional electronics, including a 3.3 V voltage regulator and level-shifting circuits, while keeping the overall size as compact as possible. The board ships fully populated with its SMD components, including the L3GD20H, as shown in the product picture. The L3GD20H has many improvements over the older L3GD20, including better accuracy and stability, lower power consumption, and a much shorter start-up time, all in a smaller package that allows the overall carrier board to be smaller. The L3GD20H also offers a wider range of user- selectable output data rates, with lower frequencies available that are more appropriate for human gesture detection, and it features a data enable (DEN) pin that allows readings to be synchronized with external triggers. While the L3GD20H carrier is not a direct drop-in replacement for the L3GD20 carrier due to differences in the pinout and sensor orientation, it should still be usable as a replacement with the appropriate wiring changes, and since the two ICs share the same register structure and IC device address, code written for one should be easily portable to the other. The L3GD20H has many configurable options, including three selectable angular rate sensitivities, seven selectable output data rates, seven different embedded FIFO modes for buffering output data, and a programmable external interrupt signal. The three angular velocity readings are available through a digital interface, which can be configured to operate in either IC or SPI mode. The carrier board includes a low-dropout linear voltage regulator that provides the 3.3 V required by the L3GD20H, which allows the sensor to be powered from 2.5 V to 5.5 V. The regulator output is available on the VDD pin and can supply almost 150 mA to external devices. The breakout board also includes a circuit that shifts the two IC lines (or SPI clock and data-in lines) to the same logic voltage level as the supplied VIN, making it simple to interface the board with 5 V systems, and the boards 0.1 pin spacing makes it easy to use with standard solderless breadboards and 0.1 perfboards. For sensor fusion applications, our MinIMU-9 v2 and AltIMU-10 inertial measurement units combine the older L3GD20 with a LSM303DLHC 3-axis accelerometer and magnetometer on a single board, providing nine independent readings that can be used to calculate an absoluteorientation. The AltIMU-10 also includes an LPS331AP pressure sensor that can be used to calculate altitude. Specifications Dimensions: 0.4 0.9 0.1 (13 23 3 mm) Weight without header pins: 0.7 g (0.03 oz) Operating voltage: 2.5 V to 5.5 V Supply current: ~6 mA Output format (IC/SPI): one 16-bit reading per axis Sensitivity range (configurable): 245/s, 500/s, or 2000/s Included components A 101 strip of 0.1 straight header pins and a 91 strip of 0.1 right-angle header pins are included, as shown in the picture below. You can solder the header strip of your choice to the board for use with custom cables or solderless breadboards, or you can solder wires directly to the board itself for more compact installations. The board has one mounting hole that works with 2 and M2 screws (not included). Using the L3GD20H Connections Regardless of the interface being used to communicate with the L3GD20H, its VIN pin should be connected to a 2.5 V to 5.5 V source, and GND should be connected to 0 volts. (Alternatively, if you are using the gyro with a 3.3 V system, you can leave VIN disconnected and bypass the built- in regulator by connecting 3.3 V directly to VDD.) A minimum of two logic connections are necessary to use the L3GD20H in IC mode (this is the default mode): SCL and SDA. These pins are connected to built-in level-shifters that make them safe to use at voltages over 3.3 V they should be connected to an IC bus operating at the same logic level as VIN. The remaining pins are not connected to level-shifters on the board and are not 5V-tolerant, but our 4-channel bidirectional logic level shifter can be used externally with those pins to achieve the same effect. To use the L3GD20H in SPI mode, four logic connections are typically used: SPC, SDI, SDO, and CS. These should be connected to an SPI bus operating at the same logic level as VIN. The SPI interface operates in 4-wire mode by default, with SDI and SDO on separate pins, but it can be configured to use 3-wire mode so that SDO shares a pin with SDI.