USB Power Supply Input Characteristics Input Voltage Rated Input Voltage : 100 ~ 240V AC Variable Input Voltage : 90V ~ 264V AC Input Current 0.4A max when input rated voltage and output rated load Input Frequency Rate Frequency : 50/60Hz Variation Frequency : 47 ~ 63Hz In-rush Current 60 Amps Max. Cold start at 240V AC input ,with rated load and 25C ambient AC Leakage Current 0.25mA Max . 240V AC input Output Characteristics Rated Output Power : 10.5W Voltage : +5V Max Load : 2.1A Load Regulation : 4.75V ~ 5.25V Unload Output Voltage : 5V ~ 5.25V Efficiency 115V AC input, the average efficiency 79.04%. Output rated load is 25%,50%,75%,100% 4 situations of average efficiency 230VAC input, the average efficiency 79.04%. Output rated load is 25%,50%,75%,100% 4 situations of average efficiency Unload standby Power : 0.1W Max. Ripple & Noise Measurement is done by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 47uF electrolysis capacitor. (Test under the condition of rated input and rated output) Voltage : +5V Current : 2100mA Ripple And Noise (Max) : 100m Vp-p Turn On Delay Time 3 second Max . 100V AC input and output Max. Load Rise Time 100ms Max. 100V AC input and output Max. Load Hold Up Time 5ms Min. 100V AC input and output Max. Load. Overshoot 10% Max. When power supply on or turn off. Environmental Requirements Operating Temperature : 0C to +40C (Full Load, Normal operation) Storage temperature : -10C to +55C (With enclosure) Relative Humidity : 5% (0C) ~ 90% (40C) 72h (Full Load, Normal operation) Vibration : Operating: IEC 721-3-3 3M3 5~9Hz, A=1.5mm www.farnell.com www.cpc.co.uk Page <1> 06/03/18 V1.0USB Power Supply Mechanical Characteristics Dropping Testing The product to be dropped from 1 meter height to a wood floor no breakage Safety Standard Safety Accord with IEC60950, EN60950, UL60950, GB4943 Note: AC pins corresponding to national standards, such as the CE that corresponds to EN60950 3000V AC Dielectric Strength Hi-Pot Primary to secondary, 3000V AC/5mA/5s. Insulation Resistance Primary to secondary : 10M Min at 500V DC Volume : 64.44mm 38.97mm 27.5mm (LWH) Weight : 100g 20g Diagram Dimensions : Millimetres Tolerance : 0.2mm Part Number Table Description Part Number USB Power Supply, 5V, 2.1A, White, Euro PEL00393 Important Notice : This data sheet and its contents (the Information) belong to the members of the Premier Farnell group of companies (the Group) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Groups liability for death or personal injury resulting from its negligence. pro - ELEC is the registered trademark of the Group. Premier Farnell Limited 2016. www.farnell.com www.cpc.co.uk Page <2> 06/03/18 V1.0