GENERAL PURPOSE Technical Data Sheet FLEXO PET Put-Ups Expansion Range Nominal Part Bulk Shop Available Lbs/ Size Spool Spool Colors 100 E conomical And Easy Min Max To Install 1/16 PTN0.06 3/64 3/32 1,000 250 *28 0.22 1/8 PTN0.13 3/32 1/4 1,000 225 *28 0.20 Resists G asoline, 1/4 PTN0.25 1/8 7/16 1,000 200 *28 0.30 Engine Chemicals 3/8 PTN0.38 3/16 1/2 500 125 *28 0.57 And Cleaning Solvents 1/2 PTN0.50 1/4 3/4 500 100 *28 0.77 5/8 PTN0.63 3/8 1 500 100 *28 0.95 Expands Up To 150% 3/4 PTN0.75 1/2 1 1/4 250 75 *28 1.20 1 PTN1.00 5/8 1 5/8 250 65 *28 1.34 C ut And Abrasion 1 1/4 PTN1.25 3/4 1 3/4 250 50 *28 1.60 Resistant 1 1/2 PTN1.50 1 2 1/8 200 40 *28 1.96 1 3/4 PTN1.75 1 1/4 2 3/4 200 30 *28 2.45 F MVSS 302 Approval 2 PTN2.00 1 1/2 3 1/2 200 50 *28 3.30 2 1/2 PTN2.50 1 3/4 3 5/8 200 50 *28 3.80 3 PTN3.00 2 1/2 4 3/4 100 50 *28 4.00 3 END CONSTRUCTION 1/4 PT30.25 1/8 3/8 1,000 200 BK, CL 0.39 9 MIL CONSTRUCTION 4 PT94.00BK 4 6 1/2 100 50 BK 3.80 PET LEAN 3/4 PTL0.75BK 1/2 1 1/4 250 75 BK 1.04 1 1/4 PTL1.25BK 3/4 1 3/4 250 50 BK 1.19 *Check for availability Colors A Versatile Bundling Available: And Protection Solution 28= See color chart The FLEXO Original braided from 10 mil polyethylene terepthalate (PET) Cut Cleanly monofilament yarns. The material has a wide Hot Knife operating temperature range, is resistant to chemical degradation, UV radiation, and abrasion. Used in electronics, automotive, Material marine and industrial wire harnessing applications Polyethylene Terepthalate where cost efficiency and durability are critical. Grade The unique braided construction and wide PTN expandability allows quick and easy installation over large connectors and long runs. Monofilament Diameter .010 High thermal and chemical resistance and wide color/size selection make FLEXO Original PET Drawing Number ideal for customizing and protecting the wires, TF001PET-WD hoses and cables in custom and classic colors. Braided Sleeving Products www.techflex.com 800.323.5140 973.300.9242 fax: 973.300.9409 29 Brookfield Dr Sparta, NJ 07871 FAR-25www.techflex.com GENERAL PURPOSE Technical Data Sheet FLEXO PET Melt Point ASTM D-2117 482F (250C) Maximum Continuous Mil-I-23053 Rating UL94VO, FAR25, Abrasion Resistance FMVSS-302 257F (125C) Medium Abrasion Test Machine Minimum Continuous Taber 5150 -94F (-70C) Abrasion Test Wheel Calibrase H-18 Abrasion Test Load 1=No Effect 4=More Affected 2=Little Effect 5=Severely Affected 500g 3=Affected Room Temperature Aromatic Solvents 2 77F Aliphatic Solvents 1 Monofilament Diameter .010 ASTM D-204 Humidity Chlorinated Solvents 3 72% Flammability Rating UL94 Weak Bases 1 FMVSS-302 Approved Two Broken Filament Salts 1 Recommended Cutting Hot Knife 300 Test Cycles Strong Bases 2 Colors 28 Approximately 6 Broken Salt Water 0-S-1926 1 Wall Thickness .025 Filaments Hydraulic Fluid MIL-H-5606 1 Tensile Strength (Yarn) 7.5 500 Test Cycles ASTM D-2256 Lbs Lube Oil MIL-L-7808 1 Material Destroyed Specific Gravity ASTM D-792 1.38 De-Icing Fluid MIL-A-8243 1 - Very Visible Hole In Material Moisture Absorption .1-.2 Strong Acids 3 % ASTM D-570 1,150 Test Cycles Strong Oxidants 2 Hard Vacuum Data ASTM E-595 at 10-5 torr Pre-Test Weight Esters/Keytones 1 TML .19 4,547.4 mg UV Light 1 CVCM .00 Post-Test Weight Petroleum 1 WVR .16 4,133.9 mg Fungus ASTM G-21 1 Smoke D-Max 56 Test End Loss Of Mass Halogen Free Yes ASTM E-662 Point Of Destruction RoHS Yes Outgassing Med 413.5 mg SVHC None Oxygen Index 21 ASTM D-2863 2012 Techflex, Inc. - Any unauthorized reproduction, in whole or part, in any medium whatsoever, without the express written permission of Techflex, Inc. is strictly forbidden. Techflex product names and logos are registered trademarks of Techflex, Inc., unless otherwise attributed. The contents and illustrations contained herein are believed to be reliable. Techflex makes no warranties as to their accuracy or completeness and disclaims any liability in connection with their use. Techflexs only obligations are those in standard terms of sale for these products and Techflex will not be liable for any consequential or other damages arising due to misuse of these products or typographical errors or omissions. 06-12 Users should make their own evaluation to determine the suitability of these products for their unique and specific applications.