Cable Tie Mountable, Black Features: One piece non-releasable mounting cable ties manufactured in natural or black nylon 6.6 These cable ties are available in lengths from 4 to our exclusive 48 strap. Cable ties will satisfy bundling requirements from 1/16 to 15 and loop tensile strengths from 18 to 175 pounds State-of-the-art robotic and raw material handling equipment assures product and material integrity throughout the manufacturing process. Overall quality is achieved through statistical analysis and quality driven operator objectives. It has attained Mil-Spec I-45208 quality ratings from a number of equipment manufacturers Specifications: Cable Tie Length : 370mm Cable Tie Width : 4.8mm Cable Tie Material : PA 6.6 (Polyamide) Cable Tie Colour : Black Tensile Strength : 0N/mm Cable Bundle Diameter Min. : 102mm Cable Diameter Max. : 102mm Fixing Hole Diameter : 4.6mm Operating Temperature : -40C to +85C Tensile Strength : 22kg NBS Smoke Generation for 6.6 Nylon Specific Optical Density Simple Thickness Energy Source At Maximum Smoke (Inch) At 2 Minutes Accumulation 1/16 Radiant (2.5 watts/sq.cm) 13 0 Radiant Plus Flaming Gas 1/8 26 1 Jets Results provided by natural bureau of standards (NBS). Results may not be directly correlated with larger fires, such as burning buildings. www.element14.com www.farnell.com www.newark.com www.cpc.co.uk Page <1> 17/10/12 V1.0Cable Tie Mountable, Black Materials for Moulded Assembly Hardware ASTM Moulded Property Test Condition Unit Method 6.6 Nylon Tensile Strength kpsi 11.2 Elongation at Break D638 +73F 50% RH % 300 Yield Strength 8.5 kpsi Shear Strength D732 Dry as Moulded (DAM) 9.6 Deformation under Load D621 2,000 psi +122F DAM % 1.4 IZOD Impact D256 +73F 50% RH ft lb/in 2.1 +73F Long Specimen 2 Tensile Impact Strength D1822 ft lb/in 240 DAM Melting Point D789 Fisher - Johns F 491 -5 Thermal Linear Expansion D696 DAM in/in/F 4 10 2 Thermal Conductivity - DAM Conche-Fitch BTU - in/h.ft .F 1.7 Brittleness Temperature D746 50% RH F -85 28 Oxygen Index D2863 DAM 50% RH %O 2 31 Test conducted on 1/4 specimens. Temperature Index for Moulded Nylon Temperature Index Minimum Hot Wire ignition Mechanical Material Thickness Electrical (Seconds) w/o Impact (Inch) (C) (C) 6.6 Nylon 0.058 125 85 15 Temperature index is the temperature at which the specific property will decrease to one-half its original value after 60,000 hours exposure at that temperature. Part Number Table Description Part Number Cable Tie, Mountable, Black, 370mm TCV370BK Important Notice : This data sheet and its contents (the Information) belong to the members of the Premier Farnell group of companies (the Group) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Groups liability for death or personal injury resulting from its negligence. pro - POWER is the registered trademark of the Group. Premier Farnell plc 2012. www.element14.com www.farnell.com www.newark.com www.cpc.co.uk Page <2> 17/10/12 V1.0