Toner Transfer PPa er The Toner Transfer Paper (or ALL PulsarProFX PRODUCTS: TTP) is a replenishment item used KITS: with both the PCB Fab-In-A-Box kit for making circuit boards, and - PCB Fab-In-A-Box 50-1003 the DecalPro kit to create pro- - PCB Fab-In-A-Box (MINI kit) 50-1006 fessional dry-transfer graphics for - Combo (PCB + DecalPro) 50-1004 enclosures, faceplates... basically - DecalPRO (10min Graphics) 50-1001 any surface, flat or curved. LAMINATOR: Toner images print perfectly to the - Applicator (12 120 vac) 50-1301C transfer paper because the printer sees this as regular soft paper (vs plastic sheet from other processes). SUPPLIES: On one side of the paper is a barrier - PAPER: Toner Transfer Paper 50-1101 coating (Dextrin) that prevents the - FOIL: GreenTRF (Etching) 50-1225 toner from fusing into the fibers of - FOIL: WhiteTRF (Silkscreen) 50-1226 the paper. - FOILS: DecalPro 50-1201 ~ 50-1299 - CARRIER BOARD: DecalPro 50-1503 Printed Circuit Board Fabrication: The circuit image is laid face-down over the copper-clad surface and subjected to high COPPER CLAD: 8 x 10 heat and pressure (using either a calibrated - 2pk Rigid .032 Single Sided 50-1501 houshold iron or the highly recommended - 2pk Rigid .032 Double Sided 50-1502 laminator (see right-panel >) upon which, - 2pk Flex .005 Single Sided 50-1504 the toner image will re-fuse to the coppers - 2pk Flex .005 Double Sided 50-1505 surface. The board and paper combination are then submerged in a tray of water where the Dextrin coating dissolves in 1 minute, releasing the image. COPPER CLAD: 6 x 8 - 4pk Rigid .032 Single Sided 50-1507 Rinse the board under tap water, dry and - 4pk Rigid .032 Double Sided 50-1508 apply the sealing GreenTRF foil the same - 4pk Sampler (Mixed)... 50-1506 way as before to SEAL the toner image to (.005 SS+DS and .032 SS+DS) prevent pitting from etchant getting through the granular toner image. This special foil goes hand-in-hand with the transfer paper. Regarding the recommended laminator: More info is available on our website at Although the direct-etch (PCB) method for PCBfx.com. applying an etching mask to copper can be done reliably after doing a simple calibration Dry-Transfer Graphics: of a houshold iron, the suggested laminator The DecalPro process is a stand-alone tech- does make it much easier and faster to use. nique to create an image that is simply rubbed- down over the intended target location with no The DecalPro process on the other hand clear carrier around the image, unlike that of does REQUIRE the use of the laminator. old-fashioned water-slide graphics. More info is available on our website at DecalProFX.com. For more information about our techniques we invite you to visit our website at PulsarProFX.com or call us at (850) 926-2009, 9am-5pm MSTX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for pulsar manufacturer: Other Similar products are found below : 50-1234 50-1218 50-1228 50-1238 50-1504 50-1506 50-1001 50-1004 50-1224 50-1201 50-1214 50-1216 50-1210 50-1236 50-1299 50- 1208 50-1503 50-1505 DECALPRO KIT (50-1001) 50-1220 50-1212 50-1226 WHITETRF (50-1226) 50-1225 50-1230 .032 SINGLE- SIDED (50-1501) 50-1222 50-1202 50-1003 GREENTRF (50-1225) 50-1502 50-1101 50-1206 50-1501 TONER TRANFER PAPER (50- 1102)