Toner r Teac ive Foils - DecalPro - ALL PulsarProFX PRODUCTS: KITS: TRF Sampler ( 1299) - PCB Fab-In-A-Box 50-1003 All 20 Toner Reactive Foils (Metallic, - PCB Fab-In-A-Box (MINI kit) 50-1006 Pigment and Special Effect) used Toner Reactive Foil Set w/Carrier & Cover CONTENTS: to colorize black toner images, in- - Combo (PCB + DecalPro) 50-1004 Qty: 20 TRF Foils Size: 8 wide x 36 long Carrier Board & Tape 1/2mil Mylar Cover Sheet cluding 2 special effect foils for full Tack Rag - DecalPRO (10min Graphics) 50-1001 color images. Metallic Foils: Note: There are 2 silver-looking foils and they are used differently Foil 12 1: Red 1202 (SILVER 1222) is put on top of black toner images, but Foil 18 (IRIDES- 2: Copper 1204 CENT 1234) is put under color toner images the same way you would use 3: Gold 1206 Foil 14 (WHITE 1226) as a color toner reflector. Also, Foil 17 (CLEAR LAMINATOR: COAT 1232) is a sealant used over color toner and looks just like Foil 21 4: Gold (Satin) 1208 (Mylar Carrier 1201). TRF Flat-Paks ( 1202~1238) 5: Green 1210 6: Green (Satin) 1212 UNPACK & HANG: It is easiest to unwrap and hang the foils vertically on a 7: Aqua 1214 wall for easy access to the foil you need. Carefully unravel the entire set of - Applicator (12 120 vac) 50-1301C 8: Blue (Cobalt) 1216 foils & set the loose fiberglass Carrier Board aside. Lay this cover sheet over Individual foil shades. Flat-Paks are 9: Blue (Royal) 1218 the chipboard stapled to the end of the foils and using a push-pin or tape, 10: Purple 1220 mount the foils to a wall with the RED foil to the front. 11: Fuchsia 1221 12: Silver 1222 CARRIER BOARD SETUP: Cut off 12 of the clear Mylar foil cover sheet a continuous 15 length by 8 wide. 13: Silver (Satin) 1224 (last foil in the stack). Lay the foil over the 11 long Carrier Board - flush to the bottom of the board then wrap the remaining 1 around the top of the board. Center and secure this end with the blue tape. Do not use any other Pigment Foils: additional cover or carrier over this board. The 1/2mil Mylar film allows 14: White 1227 max heat & pressure to reach the foil to bond to the toner image. SUPPLIES: (Mylar Carrier, below-right, is used 15: Gray 1228 16: Black 1230 CLEANING: Using the yellow Tack Rag, always wipe down the toner print and the back of the cut-to-size color foil before laying over the toner image. Special Effect Foils: If micro dust particles land over a spec of toner it will raise the foil over it for all dry-transfers created.) 17: Clear Coat 1232 preventing the foil from fusing to the toner. This can be the cause of a little - PAPER: Toner Transfer Paper 50-1101 18: Iridescent 1234 pits of black toner showing through the foil color after it has been trans- 19: Holographic Silver 1236 ferred. 20: Holographic Gold 1238 TRANSFERRING FOILS: Flip the Mylar Carrier foil back, lay the printed Carrier Board cover sheet image face-up over the board and place the cut-to-size foil (color-side up) - FOIL: GreenTRF (Etching) 50-1225 21: Mylar Carrier foil 1201 centered over the print and covering the prints borders Lay the Mylar smoothly back down and insert the wraped-around end of the board into the laminator. When the board is grabbed by the rollers, spread your fingers out over the Mylar film applying drag so the foil doesnt wrinkle. Always make two passes through - FOIL: WhiteTRF (Silkscreen) 50-1226 the laminator. Upon the second exit from the laminator, lift the Mylar Carrier and remove the foil/print off the board. Now peel the color foil back 180 over itself and discard. Voila - FOILS: DecalPro 50-1201 ~ 50-1299 - CARRIER BOARD: DecalPro 50-1503 COPPER CLAD: 8 x 10 - 2pk Rigid .032 Single Sided 50-1501 - 2pk Rigid .032 Double Sided 50-1502 - 2pk Flex .005 Single Sided 50-1504 - 2pk Flex .005 Double Sided 50-1505 COPPER CLAD: 6 x 8 - 4pk Rigid .032 Single Sided 50-1507 - 4pk Rigid .032 Double Sided 50-1508 50-1202 50-1204 50-1206 50-1208 50-1210 - 4pk Sampler (Mixed)... 50-1506 (.005 SS+DS and .032 SS+DS) 50-1212 50-1214 50-1216 50-1218 50-1220 PIGMENT PIGMENT White Gray 50-1221 50-1222 50-1224 50-1227 50-1228 SPECIAL OverCoat 50-1230 50-1232 50-1234 50-1236 50-1238 Shown with Carrier Board supporting printed page ovelaid with foil, passing through the laminator. For more information about our techniques we invite you to visit our website at PulsarProFX.com or call us at (850) 926-2009, 9am-5pm MSTX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for pulsar manufacturer: Other Similar products are found below : 50-1234 50-1218 50-1228 50-1238 50-1504 50-1506 50-1001 50-1004 50-1224 50-1201 50-1214 50-1216 50-1210 50-1236 50-1299 50- 1208 50-1503 50-1505 DECALPRO KIT (50-1001) 50-1220 50-1212 50-1226 WHITETRF (50-1226) 50-1225 50-1230 .032 SINGLE- SIDED (50-1501) 50-1222 50-1202 50-1003 GREENTRF (50-1225) 50-1502 50-1101 50-1206 50-1501 TONER TRANFER PAPER (50- 1102)