Pulse Jack SMT Power Inductors Power Beads - PA4390.XXXHLT Series E l e c t r o n i c s Current Rating: Over 100Apk Inductance Range: 100nH to 330nH Height: 10.0mm Max Footprint: 10.0mm x 7.0mm Max Halogen Free 7 Electrical Specifications 25C Operating Temperature - 40C to +130C 5 1 2 Saturation Current Inductance Inductance 3 4 6 Part Irated DCR Heating Current (A TYP) 0ADC Irated Number (ADC) (m nominal) (A TYP) (nH +/- 15%) (nH TYP) 25C 100C 125C PA4390.101HLT 100 100 68 113 86 81 PA4390.121HLT 120 120 68 94 81 78 0.185+/-10% 68 PA4390.151HLT 150 150 68 80 75 73 PA4390.331HLT 330 310 33 43 33 31 NOTES: 1. Inductance measured at 100kHz, 100mVrms. 7. In high volt*time applications, additional heating in the component can occur due to core losses in the inductor which may neccessitate derating the current in order to limit the temperature rise of the component. To deter- 2. Inductance at Irated is the value of the inductance at 25C at the listed rated current. mine the approximate total losses (or temperature rise) for a given application, the coreloss and temperature 3. The rated current as listed is either the saturation current (25C or 100C) or the heating current depending on rise curves can be used. which value is lower. 8. Parts with the HLT suffix are sold in tape and reel packaging. Pulse complies to industry standard tape and reel 4. The nominal DCR is measured from point a to point b , as shown below on the mechanical drawing. specification EIA-481. 5. The saturation current is the typical current which causes the inductance to drop by 20% at the stated ambient The tape and reel for this product has a width (W=24mm), pitch (Po=16mm) and depth (Ko=10.5mm). Samples of temperatures (25C, 100C ). This current is determined by placing the component in the specified ambient envi- these parts can be ordered by removing the HLT suffix and replacing with HL. ronment and applying a short duration pulse current 9. The temperature of the component (ambient plus temperature rise) must be within the stated operating tem- (to eliminate self-heating effects) to the component. perature range. 6. The heating current is the DC current which causes the part temperature to increase by approximately 40C when used in a typical application. Schematic Mechanical PA4390.XXXHLT PA4390.XXXHL D/C CTRY Weight 2 .74/grams Tape & Reel 300/reel Dimensions: mm Unless otherwise specified, all tolerances are 0,25 pulseelectronics.com P765.D (06/16) 1Pulse Jack SMT Power Inductors Power Beads - PA4390.XXXHLT Series E l e c t r o n i c s PA4390.XXXHL, LvsI, 25C 400 350 300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 Current (A) .101HL 25C .121HL 25C .151HL 25C .331HL 25C PA4390.XXXHL, LvsI, 100C 400 350 300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 Current (A) 101HL 100C .121HL 100C .151HL 100C .331HL 100C PA4390.XXXHL, LvsI, 125C 400 350 300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 Current (A) 101HL 125C .121HL 125C .151HL 125C .331HL 125C pulseelectronics.com P765.D (06/16) 2 Inductance (nH) Inductance (nH) Inductance (nH)