PA5004.122NLT Pulse

I A T F SMT Power Inductors High Current Composite Inductor - PA5004.XXXNLT and PM2204.XXXNLT POWER PRODUCTS Height: 3.1mm Max Footprint: 6.8mm x 6.6mm Max Current Rating: up to 40Apk Inductance Range: 0.18uH to 4.5uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5004) and Automotive (PM2204) grades Electrical Specifications 25C, Operating Temperature Range -55C to +155C 3 2 Part Number DC Resistance Inductance Rated Saturation Mechanical K Factor 100KHz, 0.1V Current Current D for TYP. MAX. 6 Commerical Automotive Core Loss uH20% A m m A 0.3 PA5004.181NLT PM2204.181NLT 0.18 32 1.6 1.75 36 358.8 5.30 PA5004.331NLT PM2204.331NLT 0.33 25 2.25 2.5 28 228.3 5.55 PA5004.561NLT PM2204.561NLT 0.56 22 3 3.31 25 167.4 5.30 PA5004.681NLT PM2204.681NLT 0.68 20 4.7 5.17 21 - 5.30 PA5004.102NLT PM2204.102NLT 1 18 5.5 6.05 18 132.2 5.20 PA5004.122NLT PM2204.122NLT 1.2 16 6.7 7.4 16 109.2 5.15 PA5004.152NLT PM2204.152NLT 1.5 15 8.3 9.13 15.5 - 5.15 PA5004.182NLT PM2204.182NLT 1.8 14 9.2 10.2 13 93 5.10 PA5004.222NLT PM2204.222NLT 2.2 10 11 12.2 11 81 5.05 PA5004.332NLT PM2204.332NLT 3.3 8 18.8 20.8 9 64.4 5.00 PA5004.452NLT PM2204.452NLT 4.5 7 23 25.3 8 49.2 5.00 Notes: 1. Actual temperature of the component during system operation (ambient plus other cooling provisions all affect the part temperature. Part temperature should be temperature rise) must be within the standard operating range. verified in the end application. 2. The saturation current is the current at which the initial inductance is guaranteed to 5. Parts shown in bold are standard catalog parts and are available through sample drop by no more than 40%. The typical inductance at a specified current can be found stock and distribution. Parts in lighter font are available but are not necessarily held on the typical performance curves. in sample stock or distribution and lead times may be longer. Please contact Pulse 3. The rated current is the DC current required to raise the component temperature by for availablity. approximately 40C. Take note that the components performanc varies depending 6. The PM2204.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The on the system condition. It is suggested that the component be tested at the system mechanical dimensions are 100% tested in production but do not necessarily meet a level, to verify the temperature rise of the component during system operation. product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. 4. The part temperature (ambient+temp rise) should not exceed 155C under worst 7. Special Characteristics case operating conditions. Circuit design, PCB trace size and thickness, airflow and Power.PulseElectronics.com P805. D (07/20) 1 1 6 9 4 90 SMT Power Inductors High Current Composite Inductor - PA5004.XXXNLT and PM2204.XXXNLT POWER PRODUCTS Mechanical PA5004.XXXNLT and PM2204.XXXNLT H A D C E XXX B F D/C SUGGESTED PAD LAYOUT FINAL LAYOUT Series Mechanical A B C D E F L G H 1.2uH & below 2.80.2 PA5004/PM2204 SEE SPEC TABLE 2.60.25 5.6 (REF) 2.5 (REF) 5.6 (REF) 6.60.2 6.40.2 1.40.2 1.5uH & below 2.80.2 All Dimensions in mm. TAPE & REEL INFO Blank portions Chip cavity Blank portions K P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) TAPE SIZE (mm) QTY A G P W K PCS/REEL 1 0 PA5004/PM2204 330 16.4 12 16 3.3 1000 Typical Performance Curves 181NLT 331NLT 0.25 100 0.45 100 0.36 80 0.20 80 0.27 60 0.15 60 0.18 40 0.10 40 0.09 20 0.05 20 0.00 0 0.00 0 0 7 14 21 28 35 0 10 20 30 40 50 DC CURRENT (A) DC CURRENT (A) Power.PulseElectronics.com P805. D (07/20) 2 Inductance uH W TEMP. RISE (C) Inductance uH L A G TEMP. RISE (C)