THT Power Inductors
Toroid - Vertical, Low Profile and Klipmount
Available in vertical, low profile and Klipmount
SMPS averaging filter
Characterized for general purpose use and ripple filters
Single-layer designs
3
Can be used as differential mode inductors in EMI filters
Electrical Specifications @ 25C - O perating Temperature -40C to 130C
Reference Operating Values Design Control Values
6 5
1 4
Vertical Low Profile Inductance IDC ET Energy Inductance 20 kHz DCR Coil Klip* Lead
OP
Part Part Typical (AMPS) (V-Sec) Storage No DC (H) Test mV ( MAX) Size Mount Diameter
Number Number (H) (J) (20%) No DC Code Package (in .003)
PE-51591NL 20 2.0 52 40 32.8 33 .060 H .020
PE-92100NL 25 2.6 30 85 20.7 22 .043 A KM1 .020
PE-92101NL PE-92401NL 50 2.6 50 169 45.7 45 .071 B KM2 .020
PE-92102NL PE-92402NL 100 2.6 90 338 94.1 90 .100 C KM3 .020
PE-92103NL 35 2.6 55 118 28.4 36 .037 B KM2 .025
PE-92104NL PE-92404NL 70 3.0 85 315 61.0 73 .052 C KM3 .025
PE-92105NL PE-92405NL 145 3.0 140 653 141.8 140 .087 D KM4 .025
PE-92106NL 285 3.0 300 1283 264.1 340 .140 E KM5 .025
PE-92107NL 450 3.0 425 2025 436.3 500 .200 F .025
PE-92108NL PE-92408NL 67 3.6 130 648 90.7 110 .045 D KM4 .032
PE-92109NL 165 4.0 240 1320 152.0 260 .070 E KM5 .032
PE-92110NL 270 4.0 350 2160 263.9 400 .100 F .032
PE-92111NL 40 4.0 70 320 37.9 57 .027 C KM3 .032
PE-51590NL 22 5.0 44 275 20.3 37 .020 G .032
PE-92112NL PE-92412NL 100 5.0 200 1250 90.7 180 .034 E KM5 .042
PE-92113NL 170 5.0 300 2125 159.7 310 .050 F .042
PE-92114NL PE-92414NL 35.6 5.0 100 688 55.6 88 .023 D KM4 .042
PE-92115NL 95 7.0 225 2328 96.0 200 .025 F .051
PE-92116NL PE-92416NL 55 7.0 150 1348 49.1 100 .017 E KM5 .051
PE-92117NL 55 10.0 175 2750 55.9 120 .013 F .064
* Parts available with KlipMount option can be ordered by adding a K suffix to the part number (i.e. PE-92100K).
1 pulseelectronics.com P635.B (02/15)THT Power Inductors
Toroid - Vertical, Low Profile and Klipmount
Relationships Between Reference and Operating Conditions
Inductance vs. Operating ET
(at reference I )
DC Max. Operating ET vs. Frequency
(at reference I )
DC
2.00
2.00
2.00
1.75
Temp. Rise
1.75
>40C
1.75
1.50 Temp. Rise
1.50
>40C
1.50
1.25
1.25
1.25
1.00
1.00
1.00
.75
.75
.75
.50
.50
.50
.25
.25
.25
0 .25 .50 .75 1.00 1.25 1.50
0 .25 .50 .75 1.00 1.25 1.50
OPERATING DC CURRENT
02030405060708090 100
REFERENCE I
DC
OPERATING ET
OPERATING FREQUENCY kHz
REFERENCE ET
Mechanical Schematic
Klipmount Package
Base material meets flammability requirements of UL 94V-0
Mechanically rigid mount
PC Board - automatic insertability
1
Lowest cost
C
A B C D H EV)
Standard
2
Typical
Package Maximum
.130 .020
3,30,508
.340 .580 .650 .29 .110
KM-1
8,64 14,73 16,51 7,37 2,79
E
D
.450 .650 .700 .325 .150 2E
KM-2
B
11,43 16,51 17,78 8,26 3,81
A
.450 .850 .950 .415 .150
KM-3
11,43 21,59 24,13 10,54 3,81
.620 .970 1.10 .475 .225
KM-4
15,50 24,64 27,94 12,07 5,72
.700 1.30 1.40 .625 .250
KM-5
17,78 33,02 35,56 15,88 6,35
Note: Units with large wire sizes may exceed B dimension.
KLIPMOUNT is a trademark of Pulse Engineering, Inc.
Inches
.010
Dimensions: Unless otherwise specified, all tolerances are
mm
0,25
2 pulseelectronics.com P635.B (02/15)
INDUCTANCE AT OPERATING I
DC
REFERENCE I
DC
INDUCTANCE AT OPERATING ET
INDUCTANCE AT REFERENCE ET
OPERATING ET FOR 40C TEMP. RISE
REFERENCE ET