PG1083.153NLT Pulse

SMT Power Inductors Round Wire Coils - PG1083NL series Inductance Range: 1.0uH to 50.0uH Height: 12.5mm Max Current Rating: up to 70Apk No Thermal Aging Footprint: 21.7mm x 21.5mm Max 1 Electrical Specifications 25C Operating Temperature -40C to +130C 5 Saturation Controlled Electrical Specs. Current Isat 2 6 Inductance Heating Current 3 7 (A TYP) Irated Core Loss Factor Size X Height Part Number Irated Idc 4 (A) (K2) (REF.) (MAX.) DCR Inductance (H Typical) (A TYP) (m) 0Adc 25C 100C MAX (H W 20%) PG1083.102NL 0.95 40 1.4 1.00 70 65 40 17.9 PG1083.152NL 1.35 40 1.4 1.50 52 45 40 26.8 0.417 PG1083.222NL 1.95 34 1.8 2.20 46 37 34 29.5 0.098 10.6 PG1083.332NL 2.70 28 2.2 3.30 37 33 28 35.4 2.50 BOTTOM PG1083.472NL 4.10 26 2.8 4.70 30 24 26 50.4 VIEW A PG1083.682NL 6.10 22 3.8 6.80 26 20 22 52.1 PG1083.103NL 8.60 17.5 6.0 10.5 22.5 18 17.5 62.6 PG1083.153NL 12.6 14 9.2 15.2 18.5 14 14.0 74.1 0.492 PG1083.253NL 21.0 11 15.0 24.5 14.5 12 11.0 93.9 0.054 12.50 1.40 PG1083.323NL 27.9 9 21.5 32.0 12.5 10 9.0 107.3 BOTTOM PG1083.503NL 45.2 7.4 32.6 50.0 10.0 8.5 7.4 134.1 VIEW B Notes: 1. Actual temperature of the component during system operation (ambient plus temperature rise) must be 7. Core loss approximation is based on published core data (at 100C): 1.378 2.864 within the standard operating range. Core Loss = K1 * (f) * (K2*I) in mW 2. Inductance at Irated is a typical inductance value for the component taken at rated current. K1 = 1.01E-9 3. The rated current as listed is either the saturation current ( 25C) or the heating current depending on f = switching frequency in KHz which value is lower. K1 & K2 = core loss factors 4. The DCR of the part is measured at an ambient temperature of 20C3C from point a to b as shown below I= delta I across the component in Ampere on the mechanical drawing. K2*I=one half of the peak to peak flux density across the component in Gauss 5. The saturation current, Isat, is the current at which the component inductance drop by 20% (typical) at an 8. Unless otherwise specified, all testing is made at 100kHz, 0.1Vac ambient temperature. This current is determined by placing the component in the specified ambient envi- 9. Optional Tape & Reel packaging can be ordered by adding a T suffix to the part number (i.e. PG1083.682NL ronment and applying a short duration pulse current (to eliminate self-heating effect) to the component. becomes PG1083.682NLT). Pulse complies with industry standard tape and reel specification EIA481. The 6. The heating current, Idc, is the DC current required to raise the component temperature by approximately tape and reel for this product has a width (W=44.0mm), pitch (Po=32.0mm). The depth (Ko) has two types: 40C. The heating current is determined by mounting the component on a typical PCB and applying current 1) 10.6 mm for parts with height of 10.6mm max, 120 pieces/reel 2) 12.9mm for the parts of 12.5mm max, for 30 minutes. The temperature is measured by placing the thermocouple on top of the unit under test. 100 pieces/reel. Take note that the components performance varies depending on the system condition. It is suggested 10. The core is a conductive material so care should be taken when mounting this component over an exposed that the component be tested at the system level, to verify the temperature rise of the component during via or if the voltage across the terminals exceeds 24V. Trickle current through the core material may gener- system operation.the components performance varies depending on the system condition. It is suggested ate additional losses and potential overheating. Please contact Pulse to discuss an alternative solution if that the component be tested at the system level, to verify the temperature rise of the component during required. system operation. Mechanicals Schematic (.571 14.50 ) (.571 14.50 ) PG1083.XXXNL SIZE X SIZE X 1 .854MAX .091 2.30 MIN .091 2.30 MIN 21.70 1 2 1 2 2 .846MAX PG1083.XXXNL 21.50 DATE CODE CTRY MFG 3 (.094 2.40 ) (.094 2.40 ) 3 3 (.098 2.50 ) (.098 2.50 ) BOTTOM VIEW A BOTTOM VIEW B Weight..........................18.6 grams TOP VIEW .571 14.50 Tape and Reel....................100/tray .197 5.00 Inches HEIGHT MAX. Dimensions: mm .157 4.00 d .006 .15 0.01 a b .689 17.50 Unless otherwise specified, all tolerences are 0,25 .157 4.0 .157 4.00 SUGGESTED LAND PATTERN SMT Power Inductors Round Wire Coils - PG1083NL series 7 S L F D O , Q G X F W D Q F H 9 6 & E L D V 682NL 100C 682NL 25C 472NL 100C + X H F Q D W F 472NL 25C X G 332NL 100C Q , 332NL 25C 222NL 100C 222NL 25C 152NL 100C 152NL 25C 102N L 25C 102NL 100C & % L D V 7 S L F D O , Q G X F W D Q F H 9 6 & E L D V 503NL 100C 503NL 25C + X 323NL 100C H F Q D W F X 323NL 25C G 253NL 100C Q , 253NL 25C 153NL 100C 153NL 25C 103NL 100C 103N L 25C & % L D V For More Information Pulse Worldwide Pulse Europe Pulse China Headquarters Pulse North China Pulse South Asia Pulse North Asia Headquarters Pulse Electronics GmbH Pulse Electronics (ShenZhen) CO., LTD Room 2704/2705 135 Joo Seng Road 3F, No. 198 15255 Innovation Drive Ste 100 Am Rottland 12 D708, Shenzhen Academy of Super Ocean Finance Ctr. 03-02 Zhongyuan Road San Diego, CA 92128 58540 Meinerzhagen Aerospace Technology, 2067 Yan An Road West PM Industrial Bldg. Zhongli City U.S.A. Germany The 10th Keji South Road, Shanghai 200336 Singapore 368363 Taoyuan County 32068 Nanshan District, Shenzhen, P.R. China Taiwan China 518057 Tel: 858 674 8100 Tel: 49 2354 777 100 Tel: 86 755 33966678 Tel: 86 21 62787060 Tel: 65 6287 8998 Tel: 886 3 4356768 Fax: 858 674 8262 Fax: 49 2354 777 168 Fax: 86 755 33966700 Fax: 86 2162786973 Fax: 65 6280 0080 Fax: 886 3 4356823 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. Copyright, 2017. Pulse Electronics, Inc. All rights reserved.