SMT Power Inductors Power Beads - PGL6215.XXXHLT Series Current Rating: Over 125Apk Inductance Range: 105nH to 200nH Height: 12.0mm Max Footprint: 12.0mm x 6.0mm Max 7 Electrical Specifications 25C Operating Temperature - 40C to +130C 5 1 2 Saturation Current Inductance 3 Inductance 6 Part Irated DCR (1-3) DCR (1-3) Heating Current (A TYP) 0ADC Irated Number (ADC) (+/- 10%) (+ 10%/-20%) (A TYP) (nH +/- 15%) (nH TYP) 25C 100C PGL6215.111HLT 105 105 77 125 106 PGL6215.121HLT 117 117 77 106 90 PGL6215.131HLT 130 130 77 100 82 0.125 mOhm 0.45 mOhm 77 PGL6215.151HLT 150 140 85 85 75 PGL6215.171HLT 170 119 70 70 60 PGL6215.201HLT 200 140 60 60 51 NOTES: 1. Inductance measured at 100kHz, 100mVrms. 7. In high volt*time applications, additional heating in the component can occur due 2. Inductance at Irated is the value of the inductance at 25C at the listed rated current. to core losses in the inductor which may neccessitate derating the current in order 3. The rated current as listed is either the saturation current (25C or 100C) or the heat- to limit the temperature rise of the component. To determine the approximate total ing current depending on which value is lower. losses (or temperature rise) for a given application, the coreloss and temperature rise curves can be used. 2. 4. The nominal DCR is measured at point , as shown below on the mechanical 8. Parts with the HLT suffix are sold in tape and reel packaging. Pulse complies to drawing. industry standard tape and reel specification EIA-481. 5. The saturation current is the typical current which causes the inductance to drop by The tape and reel for this product has a width (W=16mm), pitch (Po=12mm) and depth 20% at the stated ambient temperatures (25C, 100C ). This current is determined by (Ko=6.8mm). Samples of these parts can be ordered by removing the HLT suffix and placing the component in the specified ambient environment and applying a short replacing with HL. duration pulse current (to eliminate self-heating effects) to the component. 9. The temperature of the component (ambient plus temperature rise) must be within 6. The heating current is the DC current which causes the part temperature to increase by the stated operating temperature range. approximately 40C when used in a typical application. 10. Sample Value only. Guaranteed by Design and not tested in production Schematic Mechanical PGL6215.XXXHLT PGL6215.XXXHLT 1 2 6.0 MAX DATE CODE CTRY MFG 12.0 MAX 4 3 12.0 MAX SCHEMATIC 0.10 12 34 4SURFACES Weight: 2.74grms DCR MEASURE POINTS Tape &Reel: 320/ Reel (1.05) 7.1 (0.9) 3.10.3 4.1 Dimensions: mm 3.1 Unless otherwise specified , 12 34 1.0 all tolerances are 0.25 12.2 1.40.3 5.40.4 P911.A (06/21) PulseElectronics.com 1 2.50.3 2.40.3SMT Power Inductors Power Beads - PGL6215.XXXHLT Series TAPE & REEL INFO CIRCULAR HOLES PIN 1 INDICATOR SIDE P1 W SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) QTY TYPE W 0.30 P1 0.1 PCS/REEL PGL6215.XXXHLT 24.0 12.0 320 PGL6215.XXXHLT, L vs I, Curve 25C P911.A (06/21) PulseElectronics.com 2