RAFIX 22 FS
2
General data
RAFIX 22 FS control component range
For a mounting hole diameter of 22.3 mm to IEC 60947
Contact blocks with gold or silver contacts
Depth behind panel only 9.2 mm
Water-jet proof IP65
2 collar shapes
The contact blocks can be combined with other components on the same PCB.
The specified data apply only if actuators/signal indicators are combined with contact blocks and lamp sockets within the
same product range.
RAFIX
22 FS
Content
RAFIX 22 FS pushbuttons 2 - 152
RAFIX 22 FS pushbutton, flush lens, round collar 2 - 153
RAFIX 22 FS pushbutton, protruding lens, round collar 2 - 154
RAFIX 22 FS pushbutton, protruding front ring, round collar 2 - 155
RAFIX 22 FS pushbutton, flush lens, square collar 2 - 156
RAFIX 22 FS pushbutton, protruding lens, square collar 2 - 157
RAFIX 22 FS pushbutton, protruding front ring 2 - 158
RAFIX 22 FS selector switches 2 - 160
RAFIX 22 FS selector switch, round collar 2 - 161
RAFIX 22 FS selector switch, square collar 2 - 162
RAFIX 22 FS keylock switch 2 - 164
RAFIX 22 FS keylock switch, round collar 2 - 165
RAFIX 22 FS keylock switch, square collar 2 - 166
RAFIX 22 FS emergency stop pushbutton 2 - 168
RAFIX 22 FS emergency stop pushbutton, non-illuminated, dupe-proof to EN 418, non-blocking 2 - 169
RAFIX 22 FS emergency stop pushbutton, illuminated, dupe-proof to EN 418, non-blocking 2 - 170
RAFIX 22 FS emergency stop pushbutton, illuminated, dupe-proof to EN 418, non-blocking 2 - 170
RAFIX 22 FS signal indicator 2 - 172
RAFIX 22 FS signal indicator, round collar 2 - 173
RAFIX 22 FS signal indicator, square collar 2 - 173
RAFIX 22 FS contact blocks with gold contacts 2 - 174
RAFIX 22 FS contact block with gold contacts 2 - 175
RAFIX 22 FS contact blocks with silver contacts 2 - 176
RAFIX 22 FS contact blocks with silver contacts 2 - 177
RAFIX 22 FS special accessories 2 - 178
Blanking cap 2 - 178
Ring nut 2 - 178
LED base for signal indicators 2 - 179
Plastic frontring protection cap 2 - 179
Control components 2 - 147RAFIX 22 FS
The new RAFIX 22 FS control
component range can be combined
on a common printed circuit board
together with short-travel keys and
other components thanks to its
extremely small mounting depth of
9.2 mm.
Screw-on front ring,
made of plastic or metallized
The actuators and signal indicators
are fastened to the front panel with a
threaded ring in a 22.3 mm panel cut-
out to IEC 60947. The cast-on collar
seal made of thermoflex and an inte-
Lens
grated special membrane provide a
transparent (illuminated) or opaque
2 water-jet proof degree of protection
IP 65 to DIN.
Diffuser
(for transparent lenses only)
Actuator with
The contact blocks are soldered onto
O-ring seal and
the PCB. Illumination of the actuator
special membrane.
is provided by a 3 mm LED inserted
into the base of the contact block and
Housing with integrated
soldered to the PCB together with the
cast-on collar seal,
contact block.
front panel
thickness 1 3 mm
Threaded ring
RAFIX
22 FS
3 mm LED
The printed circuit board is fastened
to the front panel with bolts, with the
contact blocks sliding almost com-
Contact block
pletely into the actuators. In this way
(optionally with LED installed):
an extremely low profile is achieved.
1NC, 1NO, 2NC, 1NC + 1NO, 2NO
Additional advantages: Individual
(colour-coded plungers:
wiring is made unnecessary and
NC = red, NO = green)
there is no more need for a cut-out
Gold contacts for 42 V max.
in the PCB in the control component
(grey housing)
areas.
or silver contacts for max. 250 V
(black housing)
Locating pip for correct assembly
Printed circuit board
9,2 mm
2 - 148 Control Components