RAFIX 22 FS
2
General data
RAFIX 22 FS control component range
For a mounting hole diameter of 22.3 mm to IEC 60947
Contact blocks with gold or silver contacts
Depth behind panel only 9.2 mm
Water-jet proof IP65
2 collar shapes
The contact blocks can be combined with other components on the same PCB.
The specified data apply only if actuators/signal indicators are combined with contact blocks and lamp sockets within the
RAFIX
same product range.
22 FS
Content
RAFIX 22 FS pushbutton 2 - 168
RAFIX 22 FS pushbutton, flush lens, round collar 2 - 169
RAFIX 22 FS pushbutton, protruding lens, round collar 2 - 170
RAFIX 22 FS pushbutton, protruding front ring, round collar 2 - 171
RAFIX 22 FS pushbutton, flush lens, square collar 2 - 172
RAFIX 22 FS pushbutton, protruding lens, square collar 2 - 173
RAFIX 22 FS pushbutton, protruding front ring 2 - 174
RAFIX 22 FS selector switch 2 - 176
RAFIX 22 FS selector switch, round collar 2 - 177
RAFIX 22 FS selector switch, square collar 2 - 178
RAFIX 22 FS keylock switch 2 - 180
RAFIX 22 FS keylock switch, round collar 2 - 181
RAFIX 22 FS keylock switch, square collar 2 - 182
RAFIX 22 FS emergency stop pushbutton 2 - 184
RAFIX 22 FS emergency stop pushbutton, non-illuminated, dupe-proof to EN 418, non-blocking 2 - 185
RAFIX 22 FS emergency stop pushbutton, illuminated, dupe-proof to EN 418, non-blocking 2 - 185
RAFIX 22 FS signal indicator 2 - 186
RAFIX 22 FS signal indicator, round collar 2 - 187
RAFIX 22 FS signal indicator, square collar 2 - 187
RAFIX 22 FS contact block with gold contacts 2 - 188
RAFIX 22 FS contact block with gold contacts 2 - 189
RAFIX 22 FS contact blocks with silver contacts 2 - 190
RAFIX 22 FS contact blocks with silver contacts 2 - 191
RAFIX 22 FS special accessories 2 - 192
Blanking cap 2 - 192
Ring nut 2 - 192
LED base for signal indicators 2 - 193
Plastic frontring with thermoflex protective cap 2 - 193
Control components Stock items are marked 2 - 163
by bold printed order numbers.RAFIX 22 FS
The new RAFIX 22 FS control
component range can be combined
on a common printed circuit board
together with short-travel keys and
other components thanks to its
extremely small mounting depth of
9.2 mm.
Screw-on front ring,
made of plastic or metallized
The actuators and signal indicators
are fastened to the front panel with a
threaded ring in a 22.3 mm panel cut-
out to IEC 60947. The cast-on collar
seal made of thermoflex and an
Lens
integrated special membrane
transparent (illuminated) or opaque
2 provide a water-jet proof degree of
protection IP 65 to DIN.
Diffuser
(for transparent lenses only)
The contact blocks are soldered onto Actuator with
O-ring seal and
the PCB. Illumination of the actuator
special membrane.
is provided by a 3 mm LED inserted
into the base of the contact block and
Housing with integrated
soldered to the PCB together with the
cast-on collar seal,
contact block.
front panel
thickness 1 3 mm
Threaded ring
RAFIX
22 FS
3 mm LED
The printed circuit board is fastened
to the front panel with bolts, with the
contact blocks sliding almost
completely into the actuators. In this Contact block
(optionally with LED installed):
way an extremely low profile is
1NC, 1NO, 2NC, 1NC + 1NO, 2NO
achieved. Additional advantages:
(colour-coded plungers:
Individual
NC = red, NO = green)
wiring is made unnecessary and
Gold contacts for 42 V max.
there is no more need for a cut-out
(grey housing)
in the PCB in the control component
or silver contacts for max. 250 V
areas.
(black housing)
Locating pip for correct assembly
Printed circuit board
9,2 mm
2 - 164 Control Components