RAFIX 22 FS 2 General data RAFIX 22 FS control component range For a mounting hole diameter of 22.3 mm to IEC 60947 Contact blocks with gold or silver contacts Depth behind panel only 9.2 mm Water-jet proof IP65 2 collar shapes The contact blocks can be combined with other components on the same PCB. The specified data apply only if actuators/signal indicators are combined with contact blocks and lamp sockets within the same product range. RAFIX 22 FS Content RAFIX 22 FS pushbuttons 2 - 152 RAFIX 22 FS pushbutton, flush lens, round collar 2 - 153 RAFIX 22 FS pushbutton, protruding lens, round collar 2 - 154 RAFIX 22 FS pushbutton, protruding front ring, round collar 2 - 155 RAFIX 22 FS pushbutton, flush lens, square collar 2 - 156 RAFIX 22 FS pushbutton, protruding lens, square collar 2 - 157 RAFIX 22 FS pushbutton, protruding front ring 2 - 158 RAFIX 22 FS selector switches 2 - 160 RAFIX 22 FS selector switch, round collar 2 - 161 RAFIX 22 FS selector switch, square collar 2 - 162 RAFIX 22 FS keylock switch 2 - 164 RAFIX 22 FS keylock switch, round collar 2 - 165 RAFIX 22 FS keylock switch, square collar 2 - 166 RAFIX 22 FS emergency stop pushbutton 2 - 168 RAFIX 22 FS emergency stop pushbutton, non-illuminated, dupe-proof to EN 418, non-blocking 2 - 169 RAFIX 22 FS emergency stop pushbutton, illuminated, dupe-proof to EN 418, non-blocking 2 - 170 RAFIX 22 FS emergency stop pushbutton, illuminated, dupe-proof to EN 418, non-blocking 2 - 170 RAFIX 22 FS signal indicator 2 - 172 RAFIX 22 FS signal indicator, round collar 2 - 173 RAFIX 22 FS signal indicator, square collar 2 - 173 RAFIX 22 FS contact blocks with gold contacts 2 - 174 RAFIX 22 FS contact block with gold contacts 2 - 175 RAFIX 22 FS contact blocks with silver contacts 2 - 176 RAFIX 22 FS contact blocks with silver contacts 2 - 177 RAFIX 22 FS special accessories 2 - 178 Blanking cap 2 - 178 Ring nut 2 - 178 LED base for signal indicators 2 - 179 Plastic frontring protection cap 2 - 179 Control components 2 - 147RAFIX 22 FS The new RAFIX 22 FS control component range can be combined on a common printed circuit board together with short-travel keys and other components thanks to its extremely small mounting depth of 9.2 mm. Screw-on front ring, made of plastic or metallized The actuators and signal indicators are fastened to the front panel with a threaded ring in a 22.3 mm panel cut- out to IEC 60947. The cast-on collar seal made of thermoflex and an inte- Lens grated special membrane provide a transparent (illuminated) or opaque 2 water-jet proof degree of protection IP 65 to DIN. Diffuser (for transparent lenses only) Actuator with The contact blocks are soldered onto O-ring seal and the PCB. Illumination of the actuator special membrane. is provided by a 3 mm LED inserted into the base of the contact block and Housing with integrated soldered to the PCB together with the cast-on collar seal, contact block. front panel thickness 1 3 mm Threaded ring RAFIX 22 FS 3 mm LED The printed circuit board is fastened to the front panel with bolts, with the contact blocks sliding almost com- Contact block pletely into the actuators. In this way (optionally with LED installed): an extremely low profile is achieved. 1NC, 1NO, 2NC, 1NC + 1NO, 2NO Additional advantages: Individual (colour-coded plungers: wiring is made unnecessary and NC = red, NO = green) there is no more need for a cut-out Gold contacts for 42 V max. in the PCB in the control component (grey housing) areas. or silver contacts for max. 250 V (black housing) Locating pip for correct assembly Printed circuit board 9,2 mm 2 - 148 Control Components