RAC60-24SB RECOM POWER

C C S S O O R R w E E M M T T P P R R a L L R I I E E A A r V V N N A N N T T r NOT RECOMMENDED FOR NEW DESIGNS TH (LAST TIME BUY: 30 OCT 2020) 60 Watt PCB mount package Features Universal input voltage range 4kVAC isolation AC/DC Converter Low output ripple and noise Regulated Short circuit protected Output trim Converter RAC60-BRAC UL certified, CE marked Description 60 Watt 3 Power module for PCB mounting. This switching converter has a universal input voltage range with Single single outputs which are trimmable to compensate for any voltage drops on the output connections. Threaded inserts ensure mechanical fixing. Output Selection Guide Part Input Output Output Efficiency Max. Capacitive Output (1) Number Voltage Range Voltage Current typ. Load Power max. VAC VDC mA % F W RAC60-05SB 85 - 265 5 10000 82 80000 50 RAC60-09SB 85 - 265 9 6600 84 28000 60 RAC60-12SB 85 - 265 12 5000 86 14000 60 RAC60-15SB 85 - 265 15 4000 86 12000 60 22 ++ RAC60-24SB 85 - 265 24 2500 86 4000 60 RoHSRoHS REACHREACH compliantcompliant compliantcompliant 10 from 1010 from 10 RAC60-48SB 85 - 265 48 1250 86 950 60 E196683 Notes: Note1: Efficiency is tested at nominal input and full load at +25C ambient UL60950-1 certified Model Numbering EN60950-1 certified CAN/CSA-C22.2 No. 60950-1 certified EN55032 compliant RAC60- B EN55024 compliant nom. Output Power Single Output Voltage PREFERRED ALTERNATIVES Ordering Examples: Please consider these alternatives: RAC60-05SB 60 Watt 5Vout Single Output RAC60-24SB 60 Watt 24Vout Single Output RACM60-K/OF Series www.recom-power.com REV.: 3/2020 PA-1 O O P P E a C C R R O O Y M M n D D O O U U t C C C C E E y T T R R S STH (LAST TIME BUY: 30 OCT 2020) NOT RECOMMENDED FOR NEW DESIGNS RAC60-B AC/DC Converter Series Specifications (measured Ta= 25C, nom. Vin, full load and after warm-up unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. nom. Vin = 230VAC 85VAC 230VAC 265VAC (2) Input Voltage Range 100VDC 370VDC 115VAC 2A Input Current 230VAC 1A 115VAC 30A Inrush Current 2ms max., cold start 230VAC 50A No load Power Consumption 115VAC/230VAC 520mW Input Frequency Range AC Input 47Hz 63Hz Output Voltage Trimming please refer to Trim table -10% +10% Minimum Load 1% Hold-up Time 115VAC/230VAC 10ms Internal Operating Frequency 100kHz <0.5% Vout + 50mVp-p (3) Output Ripple and Noise 20MHz limited <0.2% Vout + 40mVp-p Notes: Note2: The products were submitted for safety files at AC-Input operation Note3: Measurements are made with a 0.1F and 47F MLCC in parallel across output (low ESR) Output Voltage Trimming It allows the user to increase or decrease the output voltage of the module. This is accomplished by connecting an external resistor between the Trim pin and either the +Vout or -Vout pins. With an external resistor between the Trim and -Vout pin, the output voltage increases. With an external resistor between the Trim and +Vout pin, the output voltage decreases. The values for trim resistors shown in trim tables below, the specified percentage may slightly vary. 5Vout 9Vout 12Vout 15Vout 24Vout 48Vout Trim up +10 100 +10 100 +10 100 +10 100 +10 100 +10 100 % R = 500 1M 6k 1M 4k 1M 5k 1M 12k 1M 12k 1M W up 5Vout 9Vout 12Vout 15Vout 24Vout 48Vout Trim down 100 -10 100 -10 100 -10 100 -10 100 -10 100 -10 % R = 1M 500 1M 20k 1M 40k 1M 60k 1M 110k 10M 290k W down REGULATIONS Parameter Condition Value Output Accuracy 2.0% max. Line Regulation low line to high line, full load 1.0% typ. (4) Load Regulation 5% to 100% load 1.0% typ. Notes: Note4: Operation below 5% load will not harm the converter, but specifications may not be met www.recom-power.com REV.: 3/2020 PA-2