C C S S O O R R w E E M M T T P P R R a L L R I I E E A A r V V N N A N N T T r Triac dimmable with leading or trailing edge dimmers Features Class II with SELV output (no earth required) AC/DC Converter TRIAC Dimmable Extra-large screw terminals and integrated cable clamps for easy installation LED Power factor corrected >0.95 Dimming range 1..100% Driver RACT09 Compatible with a wide range of dimmers Description 9 Watt The RACT09-xxx series are low cost, triac-dimmable, constant current 9W LED drivers available with 3 either 350mA, 500mA or 700mA full-range outputs. The drivers are Class II (double insulated) meaning TRIAC no earth connection is required. The phase angle dimming works with leading or trailing edge dimmers. The RACT09 is suitable for indoor locations up to 50C ambient temperature and is certified for building Dimmable into furniture for applications such as dimmable shelf lighting, cove lighting or accent lighting. It is CE marked (LVD + EMC + RoHS), EAC and has IEC61347-1/IEC61347-2-13 CB report certification. Single Output Selection Guide Part Input Output Output Efficiency Output Number Voltage Range Voltage Range Current min. rated load Power VAC VDC mA % W RACT09-350 198-264 13-26 350 80 9 RACT09-500 198-264 9-18 500 81 9 RACT09-700 198-264 7-13 700 76 9 22++ RoHSRoHS REACHREACH compliantcompliant compliantcompliant All LED Drivers may not be used without a load. They must be switched on the primary side only. 10 from 1010 from 10 Noncompliance may damage the LED or reduce its lifetime. M M Model Numbering RACT09- IEC/EN61347 certified Output Power Output Current IEC/EN61347-2-13 certified EN61547 certified EN62493 certifed EN55015 compliant CB report Specifications (measured Ta= 25C, 240VAC, rated load unless otherwise specified) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Input Voltage Range 198VAC 230VAC 264VAC Input Current 60mA Inrush Current full load 5A No Load Power Consumption 1W Input Frequency Range 50Hz 60Hz Power Factor full load 0.95 continued on next page www.recom-power.com REV.: 4/2020 L-1 O O P P E a C C R R O O Y M M n D D O O U U t C C C C E E y T T R R S SRACT09 AC/DC Converter Series Specifications (measured ta= 25C, 240VAC, rated load unless otherwise specified) Parameter Condition Min. Typ. Max. THD full load 25% Start-up Time 500ms Internal Operating Frequency 60kHz RACT09-350 175mA (1) Output Ripple Current RACT09-500 350mA RACT09-700 900mA Notes: Note1: Measured at 20MHz BW by using a 12 twisted pair-wie terminated with a 0.1F and 47F capacitor parallel across output REGULATIONS Parameter Condition Value Output Accuracy 5% typ. Load Regulation 5% max. Line Regulation 5% max. PROTECTION Parameter Condition Value Input Fuse fusible resistor Short Circuit Protection (SCP) Latch OFF, auto recovery after fault condition is removed RACT09-350 31VDC max. Latch OFF, auto recovery Over Voltage Protection (OVP) RACT09-500 25VDC max. after fault condition is removed RACT09-700 17VDC max. Over Load Protection (OLP) Latch OFF, auto recovery after fault condition is removed Over Temperature Protection (OTP) 110C Latch OFF, auto recovery after fault condition is removed Isolation Voltage I/P to O/P tested for 1 minute 3.75kVAC Leakage Current 5mA max. Maximum loading of automatic circuit breakers* * 230VAC, 1Ohm, 90 phase angle and max. load Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A B 36 57 69 85 C 57 87 109 134 ENVIRONMENTAL Parameter Condition Value Operating Temperature Range without derating natural convection 0.1m/s (see graph) -20C to +50C Max. Case Temperature at tc point +80C max. Operating Humidity non-condensing 5-85% RH IP Rating IP20 Pollution Degree PD2 Design Lifetime +25C ambient >30 x 10 hours continued on next page www.recom-power.com REV.: 4/2020 L-2