RP20-4815SAW Recom Power

C C S S O O R R w E E M M T T P P R R a L L R I I E E A A r V V N N A N N T T r 4:1 wide input voltage range Features 1.6kVDC isolation DC/DC Converter UL certified Efficiency up to 90% Regulated Six-sided continuous shield Converter No minimum load required RP20-AW Description 20 Watt 3 The RP20-AW series are ultraminiature wide input voltage range power DC/DC converters in a case 1 x 1 half the size of industry standard 20W converters. Despite their small size, the RP20-AW converters are fully specified devices with output currents up to 4.5 Amps, up to 90% efficiency, no minimum load, Single and Dual 1600VDC isolation, a built-in Class A EMC filter and low ripple/noise figures. The outputs are also fully protected against short circuits, overcurrent and overvoltage. The no load input current is particularly low (only 4mA/6mA). The RP20-AW series will find many uses in applications where board space and/ Output or board height is at a premium or in battery-powered systems where standby current is important. Selection Guide (1) (1) Part Number Input Output Output Input Efficiency Max. Capacitive (2) Voltage Range Voltage Current Current typ. Load VDC VDC mA mA % F (3,4) RP20-243.3SAW 9-36 3.3 4500 695 89 7000 (3,4) RP20-2405SAW 9-36 5 4000 936 89 5000 (3,4) RP20-2412SAW 9-36 12 1670 938 89 850 (3,4) RP20-2415SAW 9-36 15 1330 934 89 700 (3,4) RP20-483.3SAW 18-75 3.3 4500 356 87 7000 (3,4) RP20-4805SAW 18-75 5 4000 468 89 5000 22++ (3,4) RoHSRoHS REACHREACH RP20-4812SAW 18-75 12 1670 469 89 850 compliantcompliant compliantcompliant 10 from 1010 from 10 (3,4) E196683 RP20-4815SAW 18-75 15 1330 462 90 700 (3,4) RP20-2412DAW 9-36 12 833 936 89 500 (3,4) RP20-2415DAW 9-36 15 667 926 90 350 (3,4) RP20-4812DAW 18-75 12 833 468 89 500 (3,4) RP20-4815DAW 18-75 15 667 463 90 350 UL60950-1 certified Notes: Note1: Maximum values at nominal input voltage and full load Note2: Max. Cap load is tested at minimum Input and constant resistive load Model Numbering RP20- AW/ - (4) nom. Input Voltage Package (3) Output Voltage CTRL Logic Single or Dual Notes: Note3: standard part is without suffix P or N = without CTRL & Trim function Trim function is only available for single output with /P or /N suffix add suffix P for CTRL function with positive logic (1=ON, 0=OFF), including trim pin add suffix N for CTRL function with negative logic (0=ON, 1=OFF), including trim pin Note4: add suffix -HC for premounted Heat-sink with clamps Ordering Examples RP20-2405SAW/P = 24V input, 5V output, single, positive Logic CTRL pin RP20-4812DAW-HC = 48V input, 12V output, dual, without CTRL pin, Heat-sink premounted www.recom-power.com REV.: 5/2020 PD-1 O O P P E a C C R R O O Y M M n D D O O U U t C C C C E E y T T R R S SRP20-AW DC/DC Converter Series Specifications (measured Ta= 25C, nom. Vin, full load unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Internal Input Filter Pi-Type nom. Vin = 24VDC 9VDC 24VDC 36VDC Input Voltage Range nom. Vin = 48VDC 18VDC 48VDC 75VDC nom. Vin = 24VDC 50VDC Input Surge Voltage 1s max. nom. Vin = 48VDC 100VDC DC-DC ON 9VDC nom. Vin = 24VDC DC-DC OFF 8VDC Under Voltage Lockout (UVLO) DC-DC ON 18VDC nom. Vin = 48VDC DC-DC OFF 16VDC Output Voltage Trimming refer to OUTPUT VOLTAGE TRIMMING -10% +10% Minimum Load 0% Power up 30ms Start-up Time ON/OFF CTRL 30ms DC-DC ON Open or 3.0VDC < V < 15VDC CTRL Positive Logic (5) DC-DC OFF Short or 0VDC < V < 1.2VDC ON/OFF CTRL CTRL refer to ON/OFF CTRL DC-DC ON Short or 0VDC < V < 1.2VDC CTRL Negative Logic DC-DC OFF Open or 3.0VDC < V < 15VDC CTRL drive current -0.5mA +1.0mA Input Current of CTRL pin I CTRL DC-DC OFF 2mA Standby Current I In 3.3Vout, 5Vout 248kHz 275kHz 303kHz Internal Operating Frequency Others 297kHz 330kHz 363kHz Single 75mVp-p measured at 20MHz BW Output Ripple and Noise with a 1F M/C X7R and 10F T/C Dual 100mVp-p (6) Input Reflected Ripple Current 30mAp-p Notes: Note5: If no suffix is specified, the control pin will be omitted. If fitted, the ON/OFF control function can be positive or negative logic. The pin voltage is referenced to -Vin pin Note6: Simulated source impedance of 12H. 12H inductor in series with +Vin RP20-2405SAW Efficiency vs. Input Voltage full load Efficiency vs. Output Current 95 95 90 90 85 80 85 75 70 80 65 60 75 55 9Vin 50 70 24Vin 45 36Vin 40 65 10 20 30 40 50 60 70 80 90 100 9 12 15 18 21 24 27 30 33 36 Output Current % Input Voltage VDC continued on next page www.recom-power.com REV.: 5/2020 PD-2 Efficiency % Efficiency %