Bulletin No. DSPLE-B Drawing No. LP0671 MODEL DSPLE DATA STATION PLUS z CONVERTS NUMEROUS PROTOCOLS SIMULTANEOUSLY U C R L USUS LISTEDLISTED IND. CONT. EQ. z EXTENSIVE BUILT-IN DRIVER LIST ALLOWS EASY DATA 34AD MAPPING TO PLCs, PCs, AND SCADA SYSTEMS z 10 BASE-T/100BASE-TX ETHERNET PORT SUPPORTS FOUR SIMULTANEOUS PROTOCOLS z INDEPENDENT SERIAL PORTS PROVIDE VIRTUALLY UNLIMITED INTEGRATION METHODS z SUPPORTS UP TO NINE PROTOCOLS SIMULTANEOUSLY(with expansion card) FOR USE IN HAZARDOUS LOCATIONS: 3PWL Class I, Division 2, Groups A, B, C, and D PROGRAMMABLE CONTROLLERS GENERAL DESCRIPTION SAFETY SUMMARY The Data Station Plus was designed to act as a nexus for industrial data All safety related regulations, local codes and instructions that appear in the collection and management. With three built in serial ports and a 10 Base-T/100 manual or on equipment must be observed to ensure personal safety and to Base-TX Ethernet port, the unit performs protocol conversion, allowing prevent damage to either the instrument or equipment connected to it. If disparate devices to communicate seamlessly with one another. The Ethernet equipment is used in a manner not specified by the manufacturer, the protection port supports up to four protocols simultaneously so even Ethernet to Ethernet provided by the equipment may be impaired. conversion may be performed. Do not use the controller to directly command motors, valves, or other The CompactFlash card allows new configuration files to be loaded into the actuators not equipped with safeguards. To do so can be potentially harmful to Data Station Plus. The USB port may be used for blazing fast file downloads, or persons or equipment in the event of a fault to the controller. An independent and to mount the Data Stations CompactFlash card as an external drive to your PC. redundant temperature limit indicator with alarm outputs is strongly The Data Stations DIN rail mounting saves time and panel space and snaps recommended. easily onto standard top hat (T) profile DIN rail. SOFTWARE CAUTION: Risk of Danger. Read complete instructions prior to The Data Station is programmed with Crimson 2.0 software for Windows installation and operation of the unit. 2000 or later platforms. The software is an easy to use graphical interface which can be purchased as part of a kit that includes a manual and cables, or downloaded free of charge from www.redlion.net. WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2 THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, D, OR NON-HAZARDOUS LOCATIONS ONLY DIMENSIONS In inches (mm) CompactFlash is a registered trademark of CompactFlash Association. 1stainless steel. Installation Category I, Pollution Degree 2. SPECIFICATIONS 8. POWER CONNECTION: Removable wire clamp screw terminal block. 1. POWER: 24 VDC 10% Wire Gage Capacity: 24 AWG to 12 AWG 200 mA min., without expansion card Torque: 4.45 to 5.34 in/lb (0.5 to 0.6 N-m) 1 Amp maximum with expansion card fitted 9. MOUNTING: Snaps onto standard DIN style top hat (T) profile mounting Must use Class 2 or SELV rated power supply. rails according to EN50022 -35 x 7.5 and -35 x 15. 2. COMMUNICATIONS: 10. CERTIFICATIONS AND COMPLIANCES: USB/PG Port: Adheres to USB specification 1.1. Device only using Type B SAFETY connection. UL Listed, File E302106, UL508, CSA 22.2 No. 14-M05 WARNING - DO NOT CONNECT OR DISCONNECT CABLES LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards WHILE POWER IS APPLIED UNLESS AREA IS KNOWN TO BE UL Listed, File E317425, ANSI/ISA 12.12.01-2007, CSA 22.2 No. 213-M1987 NON-HAZARDOUS. USB PORT IS FOR SYSTEM SET-UP AND LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards DIAGNOSTICS AND IS NOT INTENDED FOR PERMANENT IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment for CONNECTION. measurement, control, and laboratory use, Part 1. ELECTROMAGNETIC COMPATIBILITY Serial Ports: Format and Baud Rates for each port are individually software Emissions and Immunity to EN 61326: Electrical Equipment for programmable up to 115,200 baud. Measurement, Control and Laboratory use. RS232/PG Port: RS232 port via RJ12 COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12 Immunity to Industrial Locations: DH485 TXEN: Transmit enable open collector, V = 15 VDC, OH 2 Electrostatic discharge EN 61000-4-2 Criterion A V = 0.5 V 25 mA max. OL 4 kV contact discharge Ethernet Port: 10 BASE-T / 100 BASE-TX 8 kV air discharge RJ45 jack is wired as a NIC (Network Interface Card). Electromagnetic RF fields EN 61000-4-3 Criterion A 3. LEDs: 10 V/m STS Status LED indicates condition of Data Station. Fast transients (burst) EN 61000-4-4 Criterion A TX/RX Transmit/Receive LEDs show serial activity. 2 kV power Ethernet Link and activity LEDs. CF CompactFlash LED indicates card status and read/write activity 2 kV signal 4. MEMORY: Surge EN 61000-4-5 Criterion A On-board User Memory: 4 Mbytes of non-volatile Flash memory. 1kV L-L,2 kV L&N-E power On-board SDRAM: 2 Mbytes RF conducted interference EN 61000-4-6 Criterion A Memory Card: CompactFlash Type II slot for Type I and Type II cards. 3 V/rms Used for optional database storage only Emissions: 5. REAL-TIME CLOCK: Typical accuracy is less than one minute per month Emissions EN 55011 Class A drift. Notes: Battery: Lithium Coin Cell. Typical lifetime of 10 years at 25 C. 1. Criterion A: Normal operation within specified limits. A Battery Low system variable is available so that the programmer can 2. This device was designed for installation in an enclosure. To avoid choose specific action(s) to occur when the battery voltage drops below electrostatic discharge to the unit in environments with static levels above its nominal voltage. 4 kV precautions should be taken when the device is mounted outside an 6. ENVIRONMENTAL CONDITIONS: enclosure. When working in an enclosure (ex. making adjustments, setting Operating Temperature Range: 0 to 50C jumpers etc.) typical anti-static precautions should be observed before Storage Temperature Range: -30 to +70C touching the unit. Operating and Storage Humidity: 80% max relative humidity, 11. WEIGHT: 15.1 oz (456.4 g) non-condensing, from 0 to 50C Vibration According to IEC 68-2-6: Operational 5 to 150 Hz, in X, Y, Z WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT direction for 1.5 hours, 2 gs. EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR Shock According to IEC 68-2-27: Operational 30 g, 11 msec in 3 directions. AREA IS KNOWN TO BE NON-HAZARDOUS. Altitude: Up to 2000 meters 7. CONSTRUCTION: Case body is burgundy high impact plastic and HARDWARE INSTALLATION DIN rail should be mounted horizontally so that the units ventilation holes are vertical in relation to cabinet orientation. A minimum clearance of 1 inch (25.4 mm) should be maintained above and below the unit in order to ensure proper thermal regulation. Figure 1 - Attach Data Station To DIN Rail 2