DATASHEET HFA1105 FN3395 Rev.8.00 330MHz, Low Power, Current Feedback Video Operational Amplifier June 6, 2006 The HFA1105 is a high speed, low power current feedback Features amplifier built with Intersils proprietary complementary Low Supply Current 5.8mA bipolar UHF-1 process. High Input Impedance . 1M This amplifier features an excellent combination of low power dissipation (58mW) and high performance. The slew Wide -3dB Bandwidth 330MHz rate, bandwidth, and low output impedance (0.08 ) make Very Fast Slew Rate 1000V/ s this amplifier a good choice for driving Flash ADCs. Gain Flatness (to 75MHz) . 0.1dB Component and composite video systems also benefit from this op amps excellent gain flatness, and good differential Differential Gain . 0.02% gain and phase specifications. The HFA1105 is ideal for Differential Phase . 0.03 interfacing to Intersils line of video crosspoint switches (HA4201, HA4600, HA4314, HA4404, HA4344), to create Pin Compatible Upgrade for CLC406 high performance, low power switchers and routers. Pb-Free Plus Anneal Available (RoHS Compliant) The HFA1105 is a low power, high performance upgrade for Applications the CLC406. For a comparable amplifier with output disable or output limiting functions, please see the data sheets for Flash A/D Drivers the HFA1145 and HFA1135 respectively. Video Switching and Routing For Military grade product, please refer to the HFA1145/883 Professional Video Processing data sheet Video Digitizing Boards/Systems Ordering Information Multimedia Systems PART PART TEMP. PKG. NUMBER MARKING RANGE (C) PACKAGE DWG. RGB Preamps HFA1105IB 1105IB -40 to 85 8 Ld SOIC M8.15 Medical Imaging HFA1105IB96 1105IB 8 Ld SOIC Tape and Reel Hand Held and Miniaturized RF Equipment HFA1105IBZ 1105IBZ -40 to 85 8 Ld SOIC M8.15 Battery Powered Communications (Note 1) (Pb-free) Pinout HFA1105IBZ96 1105IBZ 8 Ld SOIC Tape and Reel (Pb-free) (Note 1) HFA1105 (SOIC) TOP VIEW HFA11XXEVAL DIP Evaluation Board for High Speed (Note 2) Op Amps NOTES: NC 1 8 NC 1. Intersil Pb-free plus anneal products employ special Pb-free 2 7 -IN V+ - material sets molding compounds/die attach materials and + +IN 3 6 OUT 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering V- 4 5 NC operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2. Requires a SOIC-to-DIP adapter. See Evaluation Board section inside. FN3395 Rev.8.00 Page 1 of 12 June 6, 2006HFA1105 Absolute Maximum Ratings Thermal Information Supply Voltage (V+ to V-) 11V Thermal Resistance (Typical, Note 4) (C/W) JA DC Input Voltage V SUPPLY SOIC Package . 165 Differential Input Voltage . 8V Maximum Junction Temperature (Die) 175C Output Current (Note 3) .Short Circuit Protected Maximum Junction Temperature (Plastic Package) 150C 30mA Continuous Maximum Storage Temperature Range -65C to 150C 60mA 50% Duty Cycle Maximum Lead Temperature (Soldering 10s) 300C ESD Rating .>600V (Lead Tips Only) Temperature Range -40C to 85C CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 3. Output is short circuit protected to ground. Brief short circuits to ground will not degrade reliability, however continuous (100% duty cycle) output current must not exceed 30mA for maximum reliability. 4. is measured with the component mounted on an evaluation PC board in free air. JA Electrical Specifications V = 5V, A = +1, R = 510W, R = 100W, Unless Otherwise Specified SUPPLY V F L (NOTE 5) TEST TEMP. PARAMETER TEST CONDITIONS LEVEL (C) MIN TYP MAX UNITS INPUT CHARACTERISTICS Input Offset Voltage A 25 - 2 5 mV AFull - 3 8 mV Average Input Offset Voltage Drift B Full - 1 10 V/C Input Offset Voltage V = 1.8V A 25 47 50 - dB CM Common-Mode Rejection Ratio V = 1.8V A 85 45 48 - dB CM V = 1.2V A -40 45 48 - dB CM Input Offset Voltage V =1.8V A 25 50 54 - dB PS Power Supply Rejection Ratio V =1.8V A 85 47 50 - dB PS V =1.2V A -40 47 50 - dB PS Non-Inverting Input Bias Current A 25 - 6 15 A A Full - 10 25 A Non-Inverting Input Bias Current Drift B Full - 5 60 nA/C Non-Inverting Input Bias Current V =1.8V A 25 - 0.5 1 A/V PS Power Supply Sensitivity V =1.8V A 85 - 0.8 3 A/V PS V =1.2V A -40 - 0.8 3 A/V PS Non-Inverting Input Resistance V = 1.8V A 25 0.8 1.2 - M CM V = 1.8V A 85 0.5 0.8 - M CM V = 1.2V A -40 0.5 0.8 - M CM Inverting Input Bias Current A 25 - 2 7.5 A AFull - 5 15 A Inverting Input Bias Current Drift B Full - 60 200 nA/C Inverting Input Bias Current V = 1.8V A 25 - 3 6 A/V CM Common-Mode Sensitivity V = 1.8V A 85 - 4 8 A/V CM V = 1.2V A -40 - 4 8 A/V CM Inverting Input Bias Current V =1.8V A 25 - 2 5 A/V PS Power Supply Sensitivity V =1.8V A 85 - 4 8 A/V PS V =1.2V A -40 - 4 8 A/V PS FN3395 Rev.8.00 Page 2 of 12 June 6, 2006