HI-506, HI-507, HI-508, HI-509
Data Sheet June 14, 2016 FN3142.10
Single 16 and 8/Differential 8-Channel and Features
4-Channel CMOS Analog Multiplexers
Pb-Free Available (RoHS Compliant) (See Ordering Info)
The HI-506/HI-507 and HI-508/HI-509 monolithic CMOS
Low ON Resistance . . . . . . . . . . . . . . . . . . . . . . . . 180
multiplexers each include an array of sixteen and eight
Wide Analog Signal Range 15V
analog switches respectively, a digital decoder circuit for
channel selection, voltage reference for logic thresholds, and
TTL/CMOS Compatible
an enable input for device selection when several
Access Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250ns
multiplexers are present. The Dielectric Isolation (DI)
process used in fabrication of these devices eliminates the
Maximum Power Supply . . . . . . . . . . . . . . . . . . . . . . 44V
problem of latchup. DI also offers much lower substrate
Break-Before-Make Switching
leakage and parasitic capacitance than conventional junction
isolated CMOS (see Application Note AN520). No Latch-Up
Replaces DG506A/DG506AA and DG507A/DG507AA
The switching threshold for each digital input is established by
an internal +5V reference, providing a guaranteed minimum
Replaces DG508A/DG508AA and DG509A/DG509AA
2.4V for logic 1 and maximum 0.8V for logic 0. This allows
direct interface without pullup resistors to signals from most
Applications
logic families: CMOS, TTL, DTL and some PMOS. For
Data Acquisition Systems
protection against transient overvoltage, the digital inputs
include a series 200 resistor and diode clamp to each Precision Instrumentation
supply.
Demultiplexing
The HI-506 is a single 16-channel, the HI-507 is an
Selector Switch
8-channel differential, the HI-508 is a single 8-channel and
the HI-509 is a 4-channel differential multiplexer.
If input overvoltages are present, the HI-546/HI-547/HI-548/
HI-549 multiplexers are recommended.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2003, 2005, 2007, 2015, 2016. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.HI-506, HI-507, HI-508, HI-509
Ordering Information
TEMP.
PART NUMBER PART MARKING RANGE (C) PACKAGE PKG. DWG. #
HI1-0506-2 HI1-506-2 -55 to +125 28 Ld CERDIP F28.6
HI4P0506-5Z (Note 1) HI4P 506-5Z 0 to +75 28 Ld PLCC (Pb-free) N28.45
HI9P0506-9Z (Note 1) HI9P506-9Z -40 to +85 28 Ld SOIC (Pb-free) M28.3
HI3-0507-5Z (No longer HI3-507-5Z 0 to +75 28 Ld PDIP (Note 3) (Pb-free) E28.6
available, recommended
replacement: HI3-0547-5Z)
HI1-0508-2 HI1-508-2 -55 to 125 16 Ld CERDIP F16.3
HI3-0508-5Z (Note 1) HI3-508-5Z 0 to +75 16 Ld PDIP (Note 3) (Pb-free) E16.3
HI9P0508-5Z (Notes 1, 2) HI9P508-5Z 0 to +75 16 Ld SOIC (Pb-free) M16.15
HI9P0508-9Z (Note 1) HI9P508-9Z -40 to +85 16 Ld SOIC (Pb-free) M16.15
HI1-0509-2 HI1-509-2 -55 to +125 16 Ld CERDIP F16.3
HI4P0509-5Z (Notes 1, 2) (No HI4P 509-5Z 0 to +75 20 Ld PLCC (Pb-free) N20.35
longer available,
recommended replacement:
DG409DYZ)
NOTES:
1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte
tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations.
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC
J STD-020.
2. Add 96 suffix for tape and reel. Please refer to TB347 for details on reel specifications.
3. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
Submit Document Feedback FN3142.10
2
June 14, 2016